Fixing issue where using alt name for the XIO would cause a segfault when speficying the pin as an input. This will close #62

Added the ability to read a full byte from a set of channels

CHANGELOG.rst

@@ -1,3 +1,76 @@
+0.5.5
+---
+* Fix for Issue #62 where using alternate name of an XIO would cause a segfault due to trying to set pull up/down resistor setting
+
+0.5.4
+---
+* Re-enabled the polarity setting for PWM based upon Issue #61
+* Fixed a 1 letter bug was trying to write inverted to polarity when it wants inversed (such facepalm)
+* Cleaned up the polarity setting code to work when PWM is not enabled
+* Fixed the unit test for pwm to verify we can set polarity
+
+0.5.3
+---
+* Fixes to the PWM pytest
+* Added pytest for LRADC and Utilities
+* Makefile updates for all the things
+
+0.5.2
+---
+* Updating Utilties to determine CHIP Pro better
+* Updating the README to fix things
+
+0.5.0
+---
+* CHIP Pro Support
+* README Updates
+
+0.4.0
+---
+* Software Servo code added
+  - Only works on the LCD and CSI pins
+* Fixed cleanup() for the SOFTPWM and SERVO
+  - The per pin cleanup for SOFTPWM doesn't work as stop() clears up the memory for the pin used
+  - SERVO code was based on SOFTPWM, so it inherited this issue
+
+0.3.5
+---
+* Merged in brettcvz's code to read a byte of data from the GPIO
+  - Cleaned the code up and expanded it (in the low level C code) to read up to 32 bits of data
+  - Presented 8 bit and 16 bits of data functions to the Python interface with brettcvz's read_byte() and my read_word()
+* I think I finally fixed the GPIO.cleanup() code one and for all
+
+0.3.4.1
+---
+* Quick fix as I borked XIO setup as inputs with the latest change that enabled PUD
+
+0.3.4
+---
+* Pull Up/Pull Down resistor setting now available for the R8 GPIO.
+* Some general cleanup
+
+0.3.3
+----
+* Added Debug printing for all the capabilities with the toggle_debug() function
+* Added 2 functions from @streamnsight for PWM that allow for setting the period of the PWM and the Pulse Width, both in nanoseconds
+* Fixed the SPI2 overlay stuff by using the NTC overlay instead of mine.
+
+0.3.2
+----
+* Fixing issue #53 to handle the return values of the set functions in pwm_enable.
+* Start of whole library debug for #55
+
+0.3.1
+----
+* Fixing issue #50 where I broke GPIO.cleanup() and SOFTPWM.cleanup() when no input is specified.
+
+0.3.0
+----
+* Added setmode() function for GPIO to maintain compatibility with Raspberry Pi scripts, this function literally does nothing
+* Added per pin cleanup functionality for GPIO and SoftPWM so you can unexport a pin without unexporting every pin
+* Updated README to make edge detection wording a little better and to add the per pin cleanup code
+* Version update since I blasted through 3 issues on github and feel like we need a nice bump to 0.3
+
 0.2.7
 ----
 * Fix to the Enable 1.8V Pin code as it wasn't working due to bit shifting isn't allowed on a float.

CHIP_IO/LRADC.py

@@ -42,9 +42,14 @@ CURRENT_SAMPLE_RATE_FILE = "/in_voltage_sampling_frequency"
 RAW_VOLTAGE_CHAN0_FILE = "/in_voltage0_raw"
 RAW_VOLTAGE_CHAN1_FILE = "/in_voltage1_raw"
 
-def enable_debug():
+def toggle_debug():
     global DEBUG
+    if DEBUG:
+        DEBUG = False
+        print("debug disabled")
+    else:
         DEBUG = True
+        print("debug enabled")
 
 def setup(rate=250):
     # First we determine if the device exists
@@ -75,7 +80,7 @@ def get_scale_factor():
 
     # Debug
     if DEBUG:
-        print("Current LRADC Scaling Factor: {0}").format(SCALE_FACTOR)
+        print("lradc.get_scale_factor: {0}".format(SCALE_FACTOR))
 
     return SCALE_FACTOR
 
@@ -91,7 +96,7 @@ def get_allowable_sample_rates():
 
     global SAMPLE_RATES
     tmp = dat.strip().split(" ")
-    for i in xrange(len(tmp)):
+    for i in range(len(tmp)):
         if "." in tmp[i]:
             tmp[i] = float(tmp[i])
         else:
@@ -100,9 +105,9 @@ def get_allowable_sample_rates():
 
     # Debug
     if DEBUG:
-        print("Allowable Sampling Rates:")
+        print("lradc.get_allowable_sample_rates:")
         for rate in SAMPLE_RATES:
-            print("{0}").format(rate)
+            print("{0}".format(rate))
 
     return tuple(SAMPLE_RATES)
 
@@ -111,10 +116,6 @@ def set_sample_rate(rate):
     if not DEVICE_EXIST:
         raise Exception("LRADC Device does not exist")
 
-    # Debug
-    if DEBUG:
-        print("Setting Sample Rate to: {0}").format(rate)
-
     # Check to see if the rates were gathered already
     global SAMPLE_RATES
     if SAMPLE_RATES == []:
@@ -124,6 +125,10 @@ def set_sample_rate(rate):
     if rate not in SAMPLE_RATES:
         raise ValueError("Input Rate an Acceptable Value")
 
+    # Debug
+    if DEBUG:
+        print("lradc.set_sample_rate: {0}".format(rate))
+
     # Write the rate
     f = open(LRADC_BASE_DEVICE_FILE+CURRENT_SAMPLE_RATE_FILE,"w")
     mystr = "%.2f" % rate
@@ -153,7 +158,7 @@ def get_sample_rate():
 
     # Debug
     if DEBUG:
-        print("Current Sampling Rate: {0}").format(dat)
+        print("lradc.get_sample_rate: {0}".format(dat))
 
     return dat
 
@@ -171,7 +176,7 @@ def get_chan0_raw():
 
     # Debug
     if DEBUG:
-        print("CHAN0 RAW: {0}").format(dat)
+        print("lradc.get_chan0_raw: {0}".format(dat))
 
     return dat
 
@@ -189,7 +194,7 @@ def get_chan1_raw():
 
     # Debug
     if DEBUG:
-        print("CHAN1 RAW: {0}").format(dat)
+        print("lradc.get_chan1_raw: {0}".format(dat))
 
     return dat
 
@@ -205,7 +210,7 @@ def get_chan0():
 
     # Debug
     if DEBUG:
-        print("CHAN0: {0}").format(dat)
+        print("lradc.get_chan0: {0}".format(dat))
 
     return dat
 
@@ -221,7 +226,7 @@ def get_chan1():
 
     # Debug
     if DEBUG:
-        print("CHAN1: {0}").format(dat)
+        print("lradc.get_chan1: {0}".format(dat))
 
     return dat
 

CHIP_IO/OverlayManager.py

@@ -20,10 +20,12 @@
 import os
 import shutil
 import time
+import sys
+from .Utilities import is_chip_pro
 
 DEBUG = False
 
-OVERLAYINSTALLPATH = "/lib/firmware/chip_io"
+OVERLAYINSTALLPATH = "/lib/firmware/nextthingco/chip"
 OVERLAYCONFIGPATH  = "/sys/kernel/config/device-tree/overlays"
 CUSTOMOVERLAYFILEPATH = ""
 
@@ -41,8 +43,8 @@ _LOADED = {
 }
 
 _OVERLAYS = {
-  "SPI2" : "chip-spi2.dtbo",
-  "PWM0" : "chip-pwm0.dtbo",
+  "SPI2" : "sample-spi.dtbo",
+  "PWM0" : "sample-pwm.dtbo",
   "CUST" : ""
 }
 
@@ -52,9 +54,14 @@ _FOLDERS = {
   "CUST" : "chip-cust"
 }
 
-def enable_debug():
+def toggle_debug():
     global DEBUG
+    if DEBUG:
+        DEBUG = False
+        print("debug disabled")
+    else:
         DEBUG = True
+        print("debug enabled")
 
 def get_spi_loaded():
     """
@@ -155,9 +162,15 @@ def load(overlay, path=""):
             print("Custom Overlay path does not exist")
             return 1
 
+        # DETERMINE IF WE ARE A CHIP PRO AND WE ARE COMMANDED TO LOAD PWM0
+        if is_chip_pro() and overlay.upper() == "PWM0":
+            print("CHIP Pro supports PWM0 in base DTB, exiting")
+            return 1
+
         # SET UP THE OVERLAY PATH FOR OUR USE
         if overlay.upper() != "CUST":
-            opath = OVERLAYINSTALLPATH + "/" + _OVERLAYS[overlay.upper()]
+            opath = OVERLAYINSTALLPATH
+            opath += "/" + _OVERLAYS[overlay.upper()]
         else:
             opath = path
         if DEBUG:
@@ -186,6 +199,12 @@ def unload(overlay):
     global _LOADED
     if DEBUG:
         print("UNLOAD OVERLAY: {0}".format(overlay))
+    
+    # DETERMINE IF WE ARE A CHIP PRO AND WE ARE COMMANDED TO UNLOAD PWM0
+    if is_chip_pro() and overlay.upper() == "PWM0":
+        print("CHIP Pro supports PWM0 in base DTB, exiting")
+        return
+    
     # SEE IF OUR OVERLAY NAME IS IN THE KEYS
     if overlay.upper() in _OVERLAYS.keys():
         # BRUTE FORCE REMOVE AS THE DIRECTORY CONTAINS FILES

CHIP_IO/Utilities.py

@@ -28,47 +28,86 @@ import subprocess
 import glob
 import re
 
+# Global Variables
+DEBUG = False
+
+def toggle_debug():
+    global DEBUG
+    if DEBUG:
+        DEBUG = False
+        print("debug disabled")
+    else:
+        DEBUG = True
+        print("debug enabled")
+
 # Set the 1.8V-pin on the CHIP U13-header to given voltage
 # Return False on error
 def set_1v8_pin_voltage(voltage):
+    if not is_chip_pro():
         if not isinstance(voltage, int) and not isinstance(voltage, float):
             return False
         if voltage < 1.8 or voltage > 3.3:
             return False
+        if DEBUG:
+            print("Setting 1.8V Pin voltage: {0}".format(voltage))
         voltage=int(round((voltage - 1.8) / 0.1)) << 4
         if subprocess.call(["/usr/sbin/i2cset", "-f", "-y" ,"0", "0x34", "0x90", "0x03"]):
+            if DEBUG:
+                print("Pin enable command failed")
             return False
         if subprocess.call(["/usr/sbin/i2cset", "-f", "-y", "0", "0x34", "0x91", str(voltage)]):
+            if DEBUG:
+                print("Pin set voltage command failed")
             return False
         return True
+    else:
+        print("Set 1.8V Pin Voltage not supported on the CHIP Pro")
 
 # Get the voltage the 1.8V-pin on the CHIP U13-header has been configured as
 # Return False on error
 def get_1v8_pin_voltage():
+    if not is_chip_pro():
         p=subprocess.Popen(["/usr/sbin/i2cget", "-f", "-y", "0", "0x34", "0x90"], stdout=subprocess.PIPE)
         output=p.communicate()[0].decode("utf-8").strip()
         #Not configured as an output
         if output != "0x03":
+            if DEBUG:
+                print("1.8V Pin is currently disabled")
             return False
         p=subprocess.Popen(["/usr/sbin/i2cget", "-f", "-y", "0", "0x34", "0x91"], stdout=subprocess.PIPE)
         output=p.communicate()[0].decode("utf-8").strip()
         voltage=round((int(output, 16) >> 4) * 0.1 + 1.8, 1)
+        if DEBUG:
+            print("Current 1.8V Pin voltage: {0}".format(voltage))
         return voltage
+    else:
+        print("Get 1.8V Pin Voltage not supported on the CHIP Pro")
 
 # Enable 1.8V Pin on CHIP U13 Header
 def enable_1v8_pin():
+    if not is_chip_pro():
         set_1v8_pin_voltage(1.8)
+    else:
+        print("Enable 1.8V Pin not supported on the CHIP Pro")
 
 # Disable 1.8V Pin on CHIP U13 Header
 def disable_1v8_pin():
+
+    if not is_chip_pro():
+        if DEBUG:
+            print("Disabling the 1.8V Pin")
         # CANNOT USE I2C LIB AS WE NEED TO FORCE THE COMMAND DUE TO THE KERNEL OWNING THE DEVICE
         # First we have to write 0x05 to AXP-209 Register 0x91
         subprocess.call('/usr/sbin/i2cset -f -y 0 0x34 0x91 0x05', shell=True)
         # Then we have to write 0x07 to AXP-209 Register 0x90
         subprocess.call('/usr/sbin/i2cset -f -y 0 0x34 0x90 0x07', shell=True)
+    else:
+        print("Disable 1.8V Pin not supported on the CHIP Pro")
 
 # Unexport All
 def unexport_all():
+    if DEBUG:
+        print("Unexporting all the pins")
     gpios = glob.glob("/sys/class/gpio/gpio[0-9]*")
     for g in gpios:
         tmp = g.split("/")
@@ -77,3 +116,29 @@ def unexport_all():
         cmd = "echo " + num + " > /sys/class/gpio/unexport"
         subprocess.Popen(cmd,shell=True, stdout=subprocess.PIPE)
 
+# Determine Processor
+def is_chip_pro():
+    isgr8 = False
+    if DEBUG:
+        print("Determining if computer is CHIP or CHIP Pro")
+    
+    # GET FIRST LINE FROM /proc/meminfo
+    f = open("/proc/meminfo","r")
+    fline = f.readline()
+    f.close()
+    
+    # FIGURE OUT OUR TOTAL MEMORY SIZE
+    parts = fline.split()
+    mem = float(parts[1]) / 1024
+    
+    if mem > 380:
+        isgr8 = False
+        if DEBUG:
+            print("found CHIP!")
+    else:
+        isgr8 = True
+        if DEBUG:
+            print("found CHIP Pro!")
+        
+    # Return isgr8
+    return isgr8

MANIFEST.in

@@ -2,4 +2,3 @@ include distribute_setup.py
 include README.rst
 include CHANGELOG.rst
 recursive-include source *.h
-recursive-include overlays *.dts *.py

Makefile

@@ -1,19 +1,61 @@
+# PyPi Packaging
 package: clean
+	@echo " ** PACKAGING FOR PYPI **"
 	python setup.py sdist
 
+# PyPi Publishing
 publish: package
+	@echo " ** UPLOADING TO PYPI **"
 	twine upload dist/*
 
+# Clean all the things
 clean:
+	@echo " ** CLEANING CHIP_IO **"
 	rm -rf CHIP_IO.* build dist
 	rm -f *.pyo *.pyc
 	rm -f *.egg
-	rm -f overlays/*.pyo overlays/*.pyc
-tests:
-	py.test
+	rm -rf __pycache__
+	rm -rf test/__pycache__/
+	rm -rf debian/python-chip-io*
+	rm -rf debian/python3-chip-io*
 
+# Run all the tests
+tests: pytest2 pytest3
+
+# Run the tests with Python 2
+pytest2:
+	@echo " ** RUNING CHIP_IO TESTS UNDER PYTHON 2 **"
+	pushd test; python -m pytest; popd
+
+# Run the tests with Python 3
+pytest3:
+	@echo " ** RUNING CHIP_IO TESTS UNDER PYTHON 3 **"
+	pushd test; python3 -m pytest; popd
+
+# Build all the things
 build:
+	@echo " ** BUILDING CHIP_IO: PYTHON 2 **"
 	python setup.py build --force
 
+# Install all the things
 install: build
+	@echo " ** INSTALLING CHIP_IO: PYTHON 2 **"
 	python setup.py install --force
+
+# Build for Python 3
+build3:
+	@echo " ** BUILDING CHIP_IO: PYTHON 3 **"
+	python3 setup.py build --force
+
+# Install for Python 3
+install3: build3
+	@echo " ** INSTALLING CHIP_IO: PYTHON 3 **"
+	python3 setup.py install --force
+
+# Install for both Python 2 and 3
+all: install install3
+
+# Create a deb file
+debfile:
+	@echo " ** BUILDING DEBIAN PACKAGES **"
+	dpkg-buildpackage -rfakeroot -uc -b

README.rst

@@ -2,39 +2,39 @@ CHIP_IO
 ============================
 A CHIP GPIO library
 
-NOTE: Now requires the custom DTC to install the library
-
-Manual::
+Manual Installation::
 
 For Python2.7::
 
     sudo apt-get update
-    sudo apt-get install git build-essential python-dev python-pip flex bison -y
-    git clone https://github.com/atenart/dtc
-    cd dtc
-    make
-    sudo  make install PREFIX=/usr
-    cd ..
+    sudo apt-get install git build-essential python-dev python-pip flex bison chip-dt-overlays -y
     git clone git://github.com/xtacocorex/CHIP_IO.git
     cd CHIP_IO
     sudo python setup.py install
     cd ..
-    sudo rm -rf CHIP_IO
 
 For Python3::
 
     sudo apt-get update
-    sudo apt-get install git build-essential python3-dev python3-pip flex bison -y
-    git clone https://github.com/atenart/dtc
-    cd dtc
-    make
-    sudo  make install PREFIX=/usr
-    cd ..
+    sudo apt-get install git build-essential python3-dev python3-pip flex bison chip-dt-overlays -y
     git clone git://github.com/xtacocorex/CHIP_IO.git
     cd CHIP_IO
     sudo python3 setup.py install
     cd ..
-    sudo rm -rf CHIP_IO
+
+PyPi Installation::
+
+For Python2.7::
+
+    sudo apt-get update
+    sudo apt-get install git build-essential python-dev python-pip flex bison chip-dt-overlays -y
+    sudo pip install CHIP-IO
+
+For Python3::
+
+    sudo apt-get update
+    sudo apt-get install git build-essential python3-dev python3-pip flex bison chip-dt-overlays -y
+    sudo pip3 install CHIP-IO
 
 **Usage**
 
@@ -46,113 +46,115 @@ All scripts that require GPIO, PWM (HW and/or SW), and Overlay Manager need to b
 
 The following "table" is the allowable pin names that are able to be used by the library. The Name column is the normal name used on the CHIP Headers, the Alt Name column is the value used by the PocketCHIP header (if it's broken out), and the Key is the Header and Pin Number the the Pin is physically located.  Either of these 3 means is able to specify a pin in CHIP_IO.
 
-  +------------------+--------------------------+--------+
-  |   CHIP (Name)    |  PocketCHIP (Alt Name)   |  Key   |
-  +------------------+--------------------------+--------+
-  | TWI1-SDA         | KPD-I2C-SDA              | U13_9  |
-  +------------------+--------------------------+--------+
-  | TWI1-SCK         | KPD-I2C-SCL              | U13_11 |
-  +------------------+--------------------------+--------+
-  | LCD-D2           | LCD-D2                   | U13_17 |
-  +------------------+--------------------------+--------+
-  | PWM0             | PWM0                     | U13_18 |
-  +------------------+--------------------------+--------+
-  | LCD-D4           | LCD-D4                   | U13_19 |
-  +------------------+--------------------------+--------+
-  | LCD-D3           | LCD-D3                   | U13_20 |
-  +------------------+--------------------------+--------+
-  | LCD-D6           | LCD-D6                   | U13_21 |
-  +------------------+--------------------------+--------+
-  | LCD-D5           | LCD-D5                   | U13_22 |
-  +------------------+--------------------------+--------+
-  | LCD-D10          | LCD-D10                  | U13_23 |
-  +------------------+--------------------------+--------+
-  | LCD-D7           | LCD-D7                   | U13_24 |
-  +------------------+--------------------------+--------+
-  | LCD-D12          | LCD-D12                  | U13_25 |
-  +------------------+--------------------------+--------+
-  | LCD-D11          | LCD-D11                  | U13_26 |
-  +------------------+--------------------------+--------+
-  | LCD-D14          | LCD-D14                  | U13_27 |
-  +------------------+--------------------------+--------+
-  | LCD-D13          | LCD-D13                  | U13_28 |
-  +------------------+--------------------------+--------+
-  | LCD-D18          | LCD-D18                  | U13_29 |
-  +------------------+--------------------------+--------+
-  | LCD-D15          | LCD-D15                  | U13_30 |
-  +------------------+--------------------------+--------+
-  | LCD-D20          | LCD-D20                  | U13_31 |
-  +------------------+--------------------------+--------+
-  | LCD-D19          | LCD-D19                  | U13_32 |
-  +------------------+--------------------------+--------+
-  | LCD-D22          | LCD-D22                  | U13_33 |
-  +------------------+--------------------------+--------+
-  | LCD-D21          | LCD-D21                  | U13_34 |
-  +------------------+--------------------------+--------+
-  | LCD-CLK          | LCD-CLK                  | U13_35 |
-  +------------------+--------------------------+--------+
-  | LCD-D23          | LCD-D23                  | U13_36 |
-  +------------------+--------------------------+--------+
-  | LCD-VSYNC        | LCD-VSYNC                | U13_37 |
-  +------------------+--------------------------+--------+
-  | LCD-HSYNC        | LCD-HSYNC                | U13_38 |
-  +------------------+--------------------------+--------+
-  | LCD-DE           | LCD-DE                   | U13_40 |
-  +------------------+--------------------------+--------+
-  | UART1-TX         | UART-TX                  | U14_3  |
-  +------------------+--------------------------+--------+
-  | UART1-RX         | UART-RX                  | U14_5  |
-  +------------------+--------------------------+--------+
-  | LRADC            | ADC                      | U14_11 |
-  +------------------+--------------------------+--------+
-  | XIO-P0           | XIO-P0                   | U14_13 |
-  +------------------+--------------------------+--------+
-  | XIO-P1           | XIO-P1                   | U14_14 |
-  +------------------+--------------------------+--------+
-  | XIO-P2           | GPIO1                    | U14_15 |
-  +------------------+--------------------------+--------+
-  | XIO-P3           | GPIO2                    | U14_16 |
-  +------------------+--------------------------+--------+
-  | XIO-P4           | GPIO3                    | U14_17 |
-  +------------------+--------------------------+--------+
-  | XIO-P5           | GPIO4                    | U14_18 |
-  +------------------+--------------------------+--------+
-  | XIO-P6           | GPIO5                    | U14_19 |
-  +------------------+--------------------------+--------+
-  | XIO-P7           | GPIO6                    | U14_20 |
-  +------------------+--------------------------+--------+
-  | AP-EINT1         | KPD-INT                  | U14_23 |
-  +------------------+--------------------------+--------+
-  | AP-EINT3         | AP-INT3                  | U14_24 |
-  +------------------+--------------------------+--------+
-  | TWI2-SDA         | I2C-SDA                  | U14_25 |
-  +------------------+--------------------------+--------+
-  | TWI2-SCK         | I2C-SCL                  | U14_26 |
-  +------------------+--------------------------+--------+
-  | CSIPCK           | SPI-SEL                  | U14_27 |
-  +------------------+--------------------------+--------+
-  | CSICK            | SPI-CLK                  | U14_28 |
-  +------------------+--------------------------+--------+
-  | CSIHSYNC         | SPI-MOSI                 | U14_29 |
-  +------------------+--------------------------+--------+
-  | CSIVSYNC         | SPI-MISO                 | U14_30 |
-  +------------------+--------------------------+--------+
-  | CSID0            | CSID0                    | U14_31 |
-  +------------------+--------------------------+--------+
-  | CSID1            | CSID1                    | U14_32 |
-  +------------------+--------------------------+--------+
-  | CSID2            | CSID2                    | U14_33 |
-  +------------------+--------------------------+--------+
-  | CSID3            | CSID3                    | U14_34 |
-  +------------------+--------------------------+--------+
-  | CSID4            | CSID4                    | U14_35 |
-  +------------------+--------------------------+--------+
-  | CSID5            | CSID5                    | U14_36 |
-  +------------------+--------------------------+--------+
-  | CSID6            | CSID6                    | U14_37 |
-  +------------------+--------------------------+--------+
-  | CSID7            | CSID7                    | U14_38 |
-  +------------------+--------------------------+--------+
+  +------------------+--------------------------+-------------+-----------------+
+  |   CHIP (Name)    | PocketCHIP/CHIP Pro Name | CHIP Key    | HW Support      |
+  +------------------+--------------------------+-------------+-----------------+
+  | TWI1-SDA         | KPD-I2C-SDA              | U13_9       | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | TWI1-SCK         | KPD-I2C-SCL              | U13_11      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D2           | UART2-TX                 | U13_17      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | PWM0             | PWM0                     | U13_18      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | PWM1             | PWM1                     | EINT13      | CHIP PRO        |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D4           | UART2-CTS                | U13_19      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D3           | UART2-RX                 | U13_20      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D6           | LCD-D6                   | U13_21      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D5           | UART2-RTS                | U13_22      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D10          | LCD-D10                  | U13_23      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D7           | LCD-D7                   | U13_24      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D12          | LCD-D12                  | U13_25      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D11          | LCD-D11                  | U13_26      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D14          | LCD-D14                  | U13_27      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D13          | LCD-D13                  | U13_28      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D18          | LCD-D18                  | U13_29      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D15          | LCD-D15                  | U13_30      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D20          | LCD-D20                  | U13_31      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D19          | LCD-D19                  | U13_32      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D22          | LCD-D22                  | U13_33      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D21          | LCD-D21                  | U13_34      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-CLK          | LCD-CLK                  | U13_35      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-D23          | LCD-D23                  | U13_36      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-VSYNC        | LCD-VSYNC                | U13_37      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-HSYNC        | LCD-HSYNC                | U13_38      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | LCD-DE           | LCD-DE                   | U13_40      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | UART1-TX         | UART-TX                  | U14_3       | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | UART1-RX         | UART-RX                  | U14_5       | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | LRADC            | ADC                      | U14_11      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | XIO-P0           | XIO-P0                   | U14_13      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | XIO-P1           | XIO-P1                   | U14_14      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | XIO-P2           | GPIO1                    | U14_15      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | XIO-P3           | GPIO2                    | U14_16      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | XIO-P4           | GPIO3                    | U14_17      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | XIO-P5           | GPIO4                    | U14_18      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | XIO-P6           | GPIO5                    | U14_19      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | XIO-P7           | GPIO6                    | U14_20      | CHIP            |
+  +------------------+--------------------------+-------------+-----------------+
+  | AP-EINT1         | KPD-INT                  | U14_23      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | AP-EINT3         | AP-INT3                  | U14_24      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | TWI2-SDA         | I2C-SDA                  | U14_25      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | TWI2-SCK         | I2C-SCL                  | U14_26      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSIPCK           | SPI-SEL                  | U14_27      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSICK            | SPI-CLK                  | U14_28      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSIHSYNC         | SPI-MOSI                 | U14_29      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSIVSYNC         | SPI-MISO                 | U14_30      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSID0            | D0                       | U14_31      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSID1            | D1                       | U14_32      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSID2            | D2                       | U14_33      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSID3            | D3                       | U14_34      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSID4            | D4                       | U14_35      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSID5            | D5                       | U14_36      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSID6            | D6                       | U14_37      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
+  | CSID7            | D7                       | U14_38      | CHIP/CHIP PRO   |
+  +------------------+--------------------------+-------------+-----------------+
 
 **GPIO Setup**
 
@@ -169,6 +171,20 @@ You can also refer to the bin based upon its alternate name::
 
     GPIO.setup("GPIO1", GPIO.IN)
 
+**GPIO Miscellaneous**
+
+Debug can be enabled/disabled by the following command::
+
+    # Enable Debug
+    GPIO.toggle_debug()
+    
+You can determine if the hardware is a CHIP/CHIP Pro using the following::
+
+    # Determine hardware
+    # 0 For CHIP
+    # 1 For CHIP Pro
+    GPIO.is_chip_pro()
+
 **GPIO Output**
 
 Setup the pin for output, and write GPIO.HIGH or GPIO.LOW. Or you can use 1 or 0.::
@@ -184,6 +200,15 @@ Inputs work similarly to outputs.::
     import CHIP_IO.GPIO as GPIO
     GPIO.setup("CSID0", GPIO.IN)
 
+Other options when setting up pins::
+
+    # Specify pull up/pull down settings on a pin
+    GPIO.setup("CSID0", GPIO.IN, pull_up_down=GPIO.PUD_UP)
+    # Specify initial value for an output
+    GPIO.setup("CSID0", GPIO.OUT, initial=1)
+    
+Pull Up/Down values are only for pins that are provided by the R8, the XIO are not capable of this.  The allowable values are: PUD_OFF, PUD_UP, and PUD_DOWN.
+
 Polling inputs::
 
     if GPIO.input("CSID0"):
@@ -191,12 +216,21 @@ Polling inputs::
     else:
         print("LOW")
 
+Read lots of data::
+
+    # Get 8 bits of data in one shot
+    mybyte = GPIO.read_byte("LCD-D3")
+    # Get 16 bits of data in one shot
+    myword = GPIO.read_word("XIO-P4")
+
+This code was initially added by brettcvz and I cleaned it up and expanded it.
+
+The edge detection code below only works for the AP-EINT1, AP-EINT3, and XPO Pins on the CHIP.
+
 Waiting for an edge (GPIO.RISING, GPIO.FALLING, or GPIO.BOTH::
 
     GPIO.wait_for_edge(channel, GPIO.RISING)
 
-This only works for the AP-EINT1, AP-EINT3, and XPO Pins on the CHIP
-
 Detecting events::
 
     GPIO.setup("XIO-P0", GPIO.IN)
@@ -206,17 +240,42 @@ Detecting events::
     if GPIO.event_detected("XIO-P0"):
         print "event detected!"
 
+CHIP_IO can also handle adding callback functions on any pin that supports edge detection.::
+
+    def mycallback(channel):
+        print("we hit the edge we want")
+
+    GPIO.setup("GPIO3", GPIO.IN)
+    # Add Callback: Falling Edge
+    GPIO.add_event_callback("GPIO3", GPIO.FALLING, mycallback)
+    # Add Callback: Rising Edge
+    GPIO.add_event_callback("GPIO3", GPIO.RISING, mycallback)
+    # Add Callback: Both Edges
+    GPIO.add_event_callback("GPIO3", GPIO.BOTH, mycallback)
+    # Remove callback
+    GPIO.remove_event_detect("GPIO3")
+
+
 **GPIO Cleanup**
 
 To clean up the GPIO when done, do the following::
 
+    # Clean up every exported GPIO Pin
     GPIO.cleanup()
+    # Clean up a single pin (keeping everything else intact)
+    GPIO.cleanup("XIO-P0")
 
 **PWM**::
 
 Hardware PWM requires a DTB Overlay loaded on the CHIP to allow the kernel to know there is a PWM device available to use.
 ::
     import CHIP_IO.PWM as PWM
+    # Determine hardware
+    # 0 For CHIP
+    # 1 For CHIP Pro
+    PWM.is_chip_pro()
+    # Enable/Disable Debug
+    PWM.toggle_debug()
     #PWM.start(channel, duty, freq=2000, polarity=0)
     #duty values are valid 0 (off) to 100 (on)
     PWM.start("PWM0", 50)
@@ -231,6 +290,12 @@ Hardware PWM requires a DTB Overlay loaded on the CHIP to allow the kernel to kn
 **SOFTPWM**::
 
     import CHIP_IO.SOFTPWM as SPWM
+    # Determine hardware
+    # 0 For CHIP
+    # 1 For CHIP Pro
+    SPWM.is_chip_pro()
+    # Enable/Disable Debug
+    SPWM.toggle_debug()
     #SPWM.start(channel, duty, freq=2000, polarity=0)
     #duty values are valid 0 (off) to 100 (on)
     #you can choose any pin
@@ -239,6 +304,7 @@ Hardware PWM requires a DTB Overlay loaded on the CHIP to allow the kernel to kn
     SPWM.set_frequency("XIO-P7", 10)
     # To Stop SPWM
     SPWM.stop("XIO-P7")
+    # Cleanup
     SPWM.cleanup()
     #For specific polarity: this example sets polarity to 1 on start:
     SPWM.start("XIO-P7", 50, 2000, 1)
@@ -247,14 +313,36 @@ Use SOFTPWM at low speeds (hundreds of Hz) for the best results. Do not use for
 
 If using SOFTPWM and PWM at the same time, import CHIP_IO.SOFTPWM as SPWM or something different than PWM as to not confuse the library.
 
+**SERVO**::
+
+    import CHIP_IO.SERVO as SERVO
+    # Determine hardware
+    # 0 For CHIP
+    # 1 For CHIP Pro
+    SERVO.is_chip_pro()
+    # Enable/Disable Debug
+    SERVO.toggle_debug()
+    #SPWM.start(channel, angle=0, range=180)
+    #angle values are between +/- range/2)
+    #you can choose any pin except the XIO's
+    SERVO.start("CSID4", 50)
+    SERVO.set_angle("CSID4", 25.5)
+    SERVO.set_range("CSID4", 90)
+    # To Stop Servo
+    SERVO.stop("CSID4")
+    # Cleanup
+    SERVO.cleanup()
+
+The Software Servo control only works on the LCD and CSI pins.  The XIO is too slow to control.
+
 **LRADC**::
 
 The LRADC was enabled in the 4.4.13-ntc-mlc.  This is a 6 bit ADC that is 2 Volt tolerant.
 Sample code below details how to talk to the LRADC.::
 
     import CHIP_IO.LRADC as ADC
-    # Enable Debug
-    ADC.enable_debug()
+    # Enable/Disable Debug
+    ADC.toggle_debug()
     # Check to see if the LRADC Device exists
     # Returns True/False
     ADC.get_device_exists()
@@ -283,13 +371,13 @@ SPI requires a DTB Overlay to access.  CHIP_IO does not contain any SPI specific
 **Overlay Manager**::
 
 The Overlay Manager enables you to quickly load simple Device Tree Overlays.  The options for loading are:
-PWM0, SPI2, I2C1, CUST
+PWM0, SPI2, CUST.  The Overlay Manager is smart enough to determine if you are trying to load PWM on a CHIP Pro and will fail due to the base DTB for the CHIP Pro supporting PWM0/1 out of the box.
 
-Only one of each type of overlay can be loaded at a time, but all three options can be loaded simultaneously.  So you can have SPI2 and I2C1 without PWM0, but you cannot have SPI2 loaded twice.
+Only one of each type of overlay can be loaded at a time, but all three options can be loaded simultaneously.  So you can have SPI2 without PWM0, but you cannot have SPI2 loaded twice.
 ::
     import CHIP_IO.OverlayManager as OM
-    # The enable_debug() function turns on debug printing
-    #OM.enable_debug()
+    # The toggle_debug() function turns on/off debug printing
+    #OM.toggle_debug()
     # To load an overlay, feed in the name to load()
     OM.load("PWM0")
     # To verify the overlay was properly loaded, the get_ functions return booleans
@@ -318,6 +406,8 @@ CHIP_IO now supports the ability to enable and disable the 1.8V port on U13.  Th
 To use the utilities, here is sample code::
 
     import CHIP_IO.Utilities as UT
+    # Enable/Disable Debug
+    UT.toggle_debug()
     # Enable 1.8V Output
     UT.enable_1v8_pin()
     # Set 2.0V Output
@@ -332,16 +422,28 @@ To use the utilities, here is sample code::
     UT.get_1v8_pin_voltage()
     # Unexport Everything
     UT.unexport_all()
+    # Determine if you are running a CHIP/CHIP Pro
+    # This returns True if the computer is a CHIP Pro and False if it is a CHIP
+    UT.is_chip_pro()
 
 **Running tests**
 
 Install py.test to run the tests. You'll also need the python compiler package for py.test.::
 
+    # Python 2.7
     sudo apt-get install python-pytest
+    # Python 3
+    sudo apt-get install python3-pytest
 
-Execute the following in the root of the project::
+To run the tests, do the following.::
 
-    sudo py.test
+    # If only one version of Python is installed
+    # Python 2
+    sudo make pytest2
+    # Python 3
+    sudo make pytest3
+    # If more than one version of Python, run through both
+    sudo make test
 
 **Credits**
 

debian/changelog

@@ -0,0 +1,44 @@
+chip-io (0.5.5-1) unstable; urgency=low
+
+  * Fix for Issue #62 where using alternate name of an XIO would cause a segfault due to trying to set pull up/down resistor setting
+
+ -- Robert Wolterman <robert.wolterman@gmail.com>  Mon, 6 Mar 2017 17:02:00 -0600
+
+chip-io (0.5.4-1) unstable; urgency=low
+
+  * Re-enabled the polarity setting for PWM based upon Issue #61
+  * Fixed a 1 letter bug was trying to write inverted to polarity when it wants inversed (such facepalm)
+  * Cleaned up the polarity setting code to work when PWM is not enabled
+  * Fixed the unit test for pwm to verify we can set polarity
+
+ -- Robert Wolterman <robert.wolterman@gmail.com>  Sat, 4 Mar 2017 20:46:00 -0600
+
+chip-io (0.5.3-1) unstable; urgency=low
+
+  * Fixes to the PWM pytest
+  * Added pytest for LRADC and Utilities
+  * Makefile updates for all the things
+
+ -- Robert Wolterman <robert.wolterman@gmail.com>  Sun, 26 Feb 2017 20:46:00 -0600
+
+chip-io (0.5.2-1) unstable; urgency=low
+
+  * Updating Utilities to determine CHIP Pro better
+  * Updating Utilities to only run CHIP appropriate code on the CHIP and not CHIP Pro
+  * Updated README
+
+ -- Robert Wolterman <robert.wolterman@gmail.com>  Sun, 26 Feb 2017 13:56:00 -0600
+
+chip-io (0.5.0-1) unstable; urgency=low
+
+  * CHIP Pro support for PWM1, reduced GPIO capability
+  * New is_chip_pro() in each of the PWM, GPIO, SoftPWM, and Servo modules
+  * Updated README
+
+ -- Robert Wolterman <robert.wolterman@gmail.com>  Sat, 25 Feb 2017 19:00:00 -0600
+
+chip-io (0.4.0-1) unstable; urgency=low
+
+  * source package automatically created by stdeb 0.8.2
+
+ -- Robert Wolterman <robert.wolterman@gmail.com>  Sat, 18 Feb 2017 23:58:48 +0000

debian/compat

@@ -0,0 +1 @@
+9

debian/control

@@ -0,0 +1,23 @@
+Source: chip-io
+Maintainer: Robert Wolterman <robert.wolterman@gmail.com>
+Section: python
+Priority: optional
+Build-Depends: python-setuptools (>= 0.6b3), python-all-dev (>= 2.6.6-3), debhelper (>= 9), dh-python,
+               python3-all (>=3.2), python3-setuptools
+Standards-Version: 3.9.1
+
+Package: python-chip-io
+Architecture: any
+Depends: ${misc:Depends}, ${python:Depends}, ${shlibs:Depends}
+Description: A module to control CHIP IO channels
+ CHIP_IO
+ ============================
+ A CHIP GPIO library
+
+Package: python3-chip-io
+Architecture: any
+Depends: ${misc:Depends}, ${python3:Depends}, ${shlibs:Depends}
+Description: A module to control CHIP IO channels
+ CHIP_IO
+ ============================
+ A CHIP GPIO library

debian/files

@@ -0,0 +1,2 @@
+python-chip-io_0.5.4-1_armhf.deb python optional
+python3-chip-io_0.5.4-1_armhf.deb python optional

debian/rules

@@ -0,0 +1,9 @@
+#!/usr/bin/make -f
+
+# This file was automatically generated by stdeb 0.8.2 at
+# Sat, 18 Feb 2017 23:58:48 +0000
+export PYBUILD_NAME=chip-io
+
+%:
+	dh $@ --with python2,python3 --buildsystem=pybuild
+

debian/source/format

@@ -0,0 +1 @@
+3.0 (quilt)

overlays/builder.py

@@ -1,24 +0,0 @@
-from subprocess import call
-import os
-import shutil
-import glob
-import sys
-
-def compile():
-    print("Compiling DTS Files")
-    call(["dtc", "-O", "dtb", "-o", "overlays/chip-spi2.dtbo", "-b", "o", "-@", "overlays/chip-spi2.dts"])
-    call(["dtc", "-O", "dtb", "-o", "overlays/chip-pwm0.dtbo", "-b", "o", "-@", "overlays/chip-pwm0.dts"])
-
-def copy():
-    target_dir = os.environ.get('TARGET_DIR', '')
-    overlay_path = target_dir + "/lib/firmware/chip_io"
-    print("Checking for DTBO Install Path")
-    if not os.path.exists(overlay_path):
-        print("Path not found, creating "+overlay_path)
-        os.makedirs(overlay_path)
-    print("Removing old DTBO files (if applicable)")
-    for fl in glob.glob(overlay_path+"/chip-*-.dtbo"):
-        os.remove(fl)
-    print("Moving DTBO files to "+overlay_path)
-    shutil.move("overlays/chip-spi2.dtbo", overlay_path+"/chip-spi2.dtbo")
-    shutil.move("overlays/chip-pwm0.dtbo", overlay_path+"/chip-pwm0.dtbo")

overlays/chip-pwm0.dts

@@ -1,61 +0,0 @@
-/*
- * Copyright 2016 Free Electrons
- * Copyright 2016 NextThing Co
- *
- * Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-/dts-v1/;
-/plugin/;
-
-/ {
-	compatible = "nextthing,chip", "allwinner,sun5i-r8";
-
-	/* Enable the PWM */
-	fragment@0 {
-		target = <&pwm>;
-
-		__overlay__ {
-			pinctrl-names = "default";
-			pinctrl-0 = <&pwm0_pins>;
-			status = "okay";
-		};
-	};
-};

overlays/chip-spi2.dts

@@ -1,93 +0,0 @@
-/*
- * Copyright 2016, Robert Wolterman
- * This file is an amalgamation of stuff from Kolja Windeler, Maxime Ripard, and Renzo.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-/plugin/;
-
-/ {
-    compatible = "nextthing,chip", "allwinner,sun5i-r8";
-
-    /* activate the gpio for interrupt */
-    fragment@0 {
-        target-path = <&pio>;
-
-        __overlay__ {
-            chip_spi2_pins: spi2@0 {
-                allwinner,pins = "PE1", "PE2", "PE3";
-                allwinner,function = "spi2";
-                allwinner,drive = "0"; //<SUN4I_PINCTRL_10_MA>;
-                allwinner,pull = "0"; //<SUN4I_PINCTRL_NO_PULL>;
-            };
-
-            chip_spi2_cs0_pins: spi2_cs0@0 {
-                allwinner,pins = "PE0";
-                allwinner,function = "spi2";
-                allwinner,drive = "0"; //<SUN4I_PINCTRL_10_MA>;
-                allwinner,pull = "0"; //<SUN4I_PINCTRL_NO_PULL>;
-            };
-        };
-    };
-
-    /*
-     * Enable our SPI device, with an spidev device connected
-     * to it
-    */
-    fragment@1 {
-        target = <&spi2>;
-
-        __overlay__ {
-            #address-cells = <1>;
-            #size-cells = <0>;
-            pinctrl-names = "default";
-            pinctrl-0 = <&chip_spi2_pins>, <&chip_spi2_cs0_pins>;
-            status = "okay";
-
-            spi2@0 {
-                compatible = "rohm,dh2228fv";
-                reg = <0>;
-                spi-max-frequency = <24000000>;
-            };
-        };
-    };
-};
-

setup.py

@@ -1,10 +1,3 @@
-try:
-    from overlays import builder
-    builder.compile()
-    builder.copy()
-except:
-    pass
-
 import distribute_setup
 distribute_setup.use_setuptools()
 from setuptools import setup, Extension, find_packages
@@ -20,17 +13,18 @@ classifiers = ['Development Status :: 3 - Alpha',
                'Topic :: System :: Hardware']
 
 setup(name             = 'CHIP_IO',
-      version          = '0.2.7',
+      version          = '0.5.5',
       author           = 'Robert Wolterman',
       author_email     = 'robert.wolterman@gmail.com',
       description      = 'A module to control CHIP IO channels',
       long_description = open('README.rst').read() + open('CHANGELOG.rst').read(),
       license          = 'MIT',
-      keywords         = 'CHIP NextThingCo IO GPIO PWM ADC',
+      keywords         = 'CHIP NextThingCo IO GPIO PWM ADC GR8 R8',
       url              = 'https://github.com/xtacocorex/CHIP_IO/',
       classifiers      = classifiers,
       packages         = find_packages(),
       ext_modules      = [Extension('CHIP_IO.GPIO', ['source/py_gpio.c', 'source/event_gpio.c', 'source/constants.c', 'source/common.c'], extra_compile_args=['-Wno-format-security']),
                           Extension('CHIP_IO.PWM', ['source/py_pwm.c', 'source/c_pwm.c', 'source/constants.c', 'source/common.c'], extra_compile_args=['-Wno-format-security']),
-                          Extension('CHIP_IO.SOFTPWM', ['source/py_softpwm.c', 'source/c_softpwm.c', 'source/constants.c', 'source/common.c', 'source/event_gpio.c'], extra_compile_args=['-Wno-format-security'])]) #,
+                          Extension('CHIP_IO.SOFTPWM', ['source/py_softpwm.c', 'source/c_softpwm.c', 'source/constants.c', 'source/common.c', 'source/event_gpio.c'], extra_compile_args=['-Wno-format-security']),
+                          Extension('CHIP_IO.SERVO', ['source/py_servo.c', 'source/c_softservo.c', 'source/constants.c', 'source/common.c', 'source/event_gpio.c'], extra_compile_args=['-Wno-format-security'])]) #,
 #                          Extension('CHIP_IO.ADC', ['source/py_adc.c', 'source/c_adc.c', 'source/constants.c', 'source/common.c'], extra_compile_args=['-Wno-format-security']),

source/c_pwm.c

@@ -33,6 +33,7 @@ SOFTWARE.
 #include <stdlib.h>
 #include <sys/types.h>
 #include <string.h>
+#include <errno.h>
 #include <fcntl.h>
 #include <unistd.h>
 #include "c_pwm.h"
@@ -46,38 +47,14 @@ SOFTWARE.
 #define DISABLE 0
 
 // Global variables
-int pwm_initialized = 0;
-int DEBUG = 0;
-//int ENABLE = 1;
-//int DISABLE = 0;
-
-// pwm devices (future chip pro use)
-struct pwm_dev
-{
-    char key[KEYLEN+1]; /* leave room for terminating NUL byte */
-    int gpio;
-    int initialized;
-    struct pwm_dev *next;
-};
-struct pwm_dev *initialized_pwms = NULL;
-
-struct pwm_dev *lookup_initialized_pwm(const char *key)
-{
-    struct pwm_dev *dev = initialized_pwms;
-    while (dev != NULL)
-    {
-        if (strcmp(dev->key, key) == 0) {
-            return dev;
-        }
-        dev = dev->next;
-    }
-    return NULL;
-}
 
 // pwm exports
 struct pwm_exp
 {
     char key[KEYLEN+1]; /* leave room for terminating NUL byte */
+    int iscpro;
+    int gpio;
+    int initialized;
     int period_fd;
     int duty_fd;
     int polarity_fd;
@@ -103,36 +80,48 @@ struct pwm_exp *lookup_exported_pwm(const char *key)
     return NULL; /* standard for pointers */
 }
 
-int initialize_pwm(void)
+int initialize_pwm(int *initialized, int gpio)
 {
-    if (!pwm_initialized) {
+    int e_no;
+    if (!*initialized) {
         int fd, len;
         char str_gpio[80];
-        // Per https://github.com/NextThingCo/CHIP-linux/pull/4
-        // we need to export 0 here to enable pwm0
-        int gpio = 0;
 
         if (DEBUG)
-            printf(" ** EXPORTING PWM0 **\n");
+            printf(" ** initialize_pwm **\n");
         if ((fd = open("/sys/class/pwm/pwmchip0/export", O_WRONLY)) < 0)
         {
+            char err[256];
+            snprintf(err, sizeof(err), "initialize_pwm: could not open export file");
+            add_error_msg(err);
             return -1;
         }
         len = snprintf(str_gpio, sizeof(str_gpio), "%d", gpio); BUF2SMALL(str_gpio);
-        ssize_t s = write(fd, str_gpio, len);  ASSRT(s == len);
-        if (DEBUG)
-            printf(" ** IN initialize_pwm: s = %d, len = %d\n", s, len);
+        ssize_t s = write(fd, str_gpio, len); e_no = errno;
         close(fd);
         
-        pwm_initialized = 1;
+        if (s != len) {
+            char err[256];
+            snprintf(err, sizeof(err), "initialize_pwm: could not export pwm (%s)", strerror(e_no));
+            add_error_msg(err);
+            return -1;
+        }
+        
+        if (DEBUG)
+            printf(" ** initialize_pwm: export pin: s = %d, len = %d\n", s, len);
+        
+        *initialized = 1;
         return 1;
+    } else {
+        if (DEBUG)
+            printf(" ** initialize_pwm: pwm is already initialized\n");
     }
 
     return 0;
 }
 
 int pwm_set_frequency(const char *key, float freq) {
-    int len;
+    int len, e_no;
     int rtnval = -1;
     char buffer[80];
     unsigned long period_ns;
@@ -150,18 +139,20 @@ int pwm_set_frequency(const char *key, float freq) {
     period_ns = (unsigned long)(1e9 / freq);
 
     if (pwm->enable) {
-        if (DEBUG)
-            printf(" ** IN pwm_set_frequency: pwm_initialized = %d\n", pwm_initialized);
         if (period_ns != pwm->period_ns) {
             pwm->period_ns = period_ns;
 
             len = snprintf(buffer, sizeof(buffer), "%lu", period_ns); BUF2SMALL(buffer);
-            if (DEBUG)
+            ssize_t s = write(pwm->period_fd, buffer, len);  e_no = errno;
+            if (DEBUG) {
+                printf(" ** pwm_set_frequency: pwm_initialized = %d\n", pwm->initialized);
                 printf(" ** pwm_set_frequency: buffer: %s\n", buffer);
-            ssize_t s = write(pwm->period_fd, buffer, len);  //ASSRT(s == len);
-            if (DEBUG)
-                printf(" ** IN pwm_set_frequency: s = %d, len = %d\n", s, len);
+                printf(" ** pwm_set_frequency: s = %d, len = %d\n", s, len);
+            }
             if (s != len) {
+                char err[256];
+                snprintf(err, sizeof(err), "pwm_set_frequency: could not change frequency of pwm (%s)", strerror(e_no));
+                add_error_msg(err);
                 rtnval = -1;
             } else {
                 rtnval = 1;
@@ -176,8 +167,71 @@ int pwm_set_frequency(const char *key, float freq) {
     return rtnval;
 }
 
+int pwm_set_period_ns(const char *key, unsigned long period_ns) {
+    int len, e_no;
+    int rtnval = -1;
+    char buffer[80];
+    struct pwm_exp *pwm;
+
+    //TODO: ADD CHECK FOR period_ns
+
+    pwm = lookup_exported_pwm(key);
+
+    if (pwm == NULL) {
+        return rtnval;
+    }
+    
+    if (pwm->enable) {
+        if (period_ns != pwm->period_ns) {
+            pwm->period_ns = period_ns;
+
+            len = snprintf(buffer, sizeof(buffer), "%lu", period_ns); BUF2SMALL(buffer);
+            ssize_t s = write(pwm->period_fd, buffer, len);  e_no = errno;
+            if (DEBUG) {
+                printf(" ** pwm_set_period_ns: pwm_initialized = %d\n", pwm->initialized);
+                printf(" ** pwm_set_period_ns: buffer: %s\n", buffer);
+                printf(" ** pwm_set_period_ns: s = %d, len = %d\n", s, len);
+            }
+            if (s != len) {
+                char err[256];
+                snprintf(err, sizeof(err), "pwm_set_period_ns: could not change period of pwm (%s)", strerror(e_no));
+                add_error_msg(err);
+                rtnval = -1;
+            } else {
+                rtnval = 1;
+            }
+        } else {
+            rtnval = 0;
+        }
+    } else {
+        rtnval = 0;
+    }
+
+    return rtnval;
+}
+
+int pwm_get_period_ns(const char *key, unsigned long *period_ns) {
+    int rtnval = -1;
+    struct pwm_exp *pwm;
+    
+    pwm = lookup_exported_pwm(key);
+
+    if (pwm == NULL) {
+        return rtnval;
+    }
+    
+    if (DEBUG)
+        printf(" ** pwm_get_period_ns: %lu **\n",pwm->period_ns);
+    
+    // Set period_ns to what we have in the struct
+    *period_ns = pwm->period_ns;
+    
+    rtnval = 0;
+    return rtnval;
+}
+
 int pwm_set_polarity(const char *key, int polarity) {
-    int len;
+    int len, e_no;
     int rtnval = -1;
     char buffer[80];
     struct pwm_exp *pwm;
@@ -192,22 +246,25 @@ int pwm_set_polarity(const char *key, int polarity) {
         return rtnval;
     }
 
-    if (pwm->enable) {
-        if (DEBUG)
-            printf(" ** IN pwm_set_polarity: pwm_initialized = %d\n", pwm_initialized);
+    // THIS ONLY WORKS WHEN PWM IS NOT ENABLED
+    if (pwm->enable == 0) {
         if (polarity == 0) {
             len = snprintf(buffer, sizeof(buffer), "%s", "normal"); BUF2SMALL(buffer);
         }
         else
         {
-            len = snprintf(buffer, sizeof(buffer), "%s", "inverted"); BUF2SMALL(buffer);
+            len = snprintf(buffer, sizeof(buffer), "%s", "inversed"); BUF2SMALL(buffer);
+        }
+        ssize_t s = write(pwm->polarity_fd, buffer, len);  e_no = errno;
+        if (DEBUG) {
+            printf(" ** pwm_set_polarity: pwm_initialized = %d\n", pwm->initialized);
+            printf(" ** pwm_set_polarity: buffer: %s\n", buffer);
+            printf(" ** pwm_set_polarity: s = %d, len = %d\n", s, len);
         }
-        if (DEBUG)
-            printf(" ** pwm_set_poliarity: buffer: %s\n", buffer);
-        ssize_t s = write(pwm->polarity_fd, buffer, len);  //ASSRT(s == len);
-        if (DEBUG)
-            printf(" ** IN pwm_set_polarity: s = %d, len = %d\n", s, len);
         if (s != len) {
+            char err[256];
+            snprintf(err, sizeof(err), "pwm_set_polarity: could not change polarity of pwm (%s)", strerror(e_no));
+            add_error_msg(err);
             rtnval = -1;
         } else {
             rtnval = 1;
@@ -215,11 +272,12 @@ int pwm_set_polarity(const char *key, int polarity) {
     } else {
         rtnval = 0;
     }
+
     return rtnval;
 }
 
 int pwm_set_duty_cycle(const char *key, float duty) {
-    int len;
+    int len, e_no;
     int rtnval = -1;
     char buffer[80];
     struct pwm_exp *pwm;
@@ -237,15 +295,17 @@ int pwm_set_duty_cycle(const char *key, float duty) {
     pwm->duty = (unsigned long)(pwm->period_ns * (duty / 100.0));
 
     if (pwm->enable) {
-        if (DEBUG)
-            printf(" ** IN pwm_set_duty_cycle: pwm_initialized = %d\n", pwm_initialized);
         len = snprintf(buffer, sizeof(buffer), "%lu", pwm->duty); BUF2SMALL(buffer);
-        if (DEBUG)
+        ssize_t s = write(pwm->duty_fd, buffer, len);  e_no = errno;
+        if (DEBUG) {
+            printf(" ** pwm_set_duty_cycle: pwm_initialized = %d\n", pwm->initialized);
             printf(" ** pwm_set_duty_cycle: buffer: %s\n", buffer);
-        ssize_t s = write(pwm->duty_fd, buffer, len);  //ASSRT(s == len);
-        if (DEBUG)
-            printf(" ** IN pwm_set_duty_cycle: s = %d, len = %d\n", s, len);
+            printf(" ** pwm_set_duty_cycle: s = %d, len = %d\n", s, len);
+        }
         if (s != len) {
+            char err[256];
+            snprintf(err, sizeof(err), "pwm_set_duty_cycle: could not change duty cycle of pwm (%s)", strerror(e_no));
+            add_error_msg(err);
             rtnval = -1;
         } else {
             rtnval = 1;
@@ -257,16 +317,57 @@ int pwm_set_duty_cycle(const char *key, float duty) {
     return rtnval;
 }
 
+int pwm_set_pulse_width_ns(const char *key, unsigned long pulse_width_ns) {
+    int len, e_no;
+    int rtnval = -1;
+    char buffer[80];
+    struct pwm_exp *pwm;
+
+    pwm = lookup_exported_pwm(key);
+
+    if (pwm == NULL) {
+        return rtnval;
+    }
+
+    if (pulse_width_ns < 0 || pulse_width_ns > pwm->period_ns)
+        return rtnval;
+
+    pwm->duty = pulse_width_ns / pwm->period_ns;
+    
+    if (pwm->enable) {
+        len = snprintf(buffer, sizeof(buffer), "%lu", pwm->duty); BUF2SMALL(buffer);
+        ssize_t s = write(pwm->duty_fd, buffer, len);  e_no = errno;
+        if (DEBUG) {
+            printf(" ** pwm_set_pulse_width_ns: pwm_initialized = %d\n", pwm->initialized);
+            printf(" ** pwm_set_pulse_width_ns: buffer: %s\n", buffer);
+            printf(" ** pwm_set_pulse_width_ns: s = %d, len = %d\n", s, len);
+        }
+        if (s != len) {
+            char err[256];
+            snprintf(err, sizeof(err), "pwm_set_pulse_width_ns: could not change pulse width of pwm (%s)", strerror(e_no));
+            add_error_msg(err);
+            rtnval = -1;
+        } else {
+            rtnval = 1;
+        }
+    } else {
+        rtnval = 0;
+    }
+
+    return rtnval;
+       
+}
+
 int pwm_set_enable(const char *key, int enable)
 {
-    int len;
+    int len, e_no;
     int rtnval = -1;
     char buffer[80];
     struct pwm_exp *pwm;
 
     if (enable != 0 && enable != 1) {
         if (DEBUG)
-            printf(" ** INVALID ENABLE OPTION, NEEDS TO BE EITHER 0 OR 1! **\n");
+            printf(" ** pwm_set_enable: enable needs to be 0 or 1! **\n");
         return rtnval;
     }
 
@@ -274,26 +375,29 @@ int pwm_set_enable(const char *key, int enable)
 
     if (pwm == NULL) {
         if (DEBUG)
-            printf(" ** SOMETHING BAD HAPPEND IN pwm_set_enable, WE'RE EXITING WITH -1 NOW! **\n");
+            printf(" ** pwm_set_enable: pwm struct is null **\n");
         return rtnval;
     }
 
 
     len = snprintf(buffer, sizeof(buffer), "%d", enable); BUF2SMALL(buffer);
-    ssize_t s = write(pwm->enable_fd, buffer, len);  //ASSRT(s == len);
+    ssize_t s = write(pwm->enable_fd, buffer, len);  e_no = errno;
     if (DEBUG) {
-        printf(" ** IN pwm_set_enable: pwm_initialized = %d\n", pwm_initialized);
+        printf(" ** pwm_set_enable: pwm_initialized = %d\n", pwm->initialized);
         printf(" ** pwm_set_enable: buffer: %s\n", buffer);
-        printf(" ** IN pwm_set_enable: s = %d, len = %d\n", s, len);
+        printf(" ** pwm_set_enable: s = %d, len = %d\n", s, len);
     }
 
     if (s == len)
     {
         if (DEBUG)
-            printf(" ** SETTING pwm->enable to %d\n", enable);
+            printf(" ** pwm_set_enable: pwm->enable to %d\n", enable);
         pwm->enable = enable;
         rtnval = 0;
     } else {
+        char err[256];
+        snprintf(err, sizeof(err), "pwm_set_enable: could not enable/disable pwm (%s)", strerror(e_no));
+        add_error_msg(err);
         rtnval = -1;
     }
 
@@ -309,21 +413,35 @@ int pwm_start(const char *key, float duty, float freq, int polarity)
     char polarity_path[80];
     int period_fd, duty_fd, polarity_fd, enable_fd;
     struct pwm_exp *new_pwm, *pwm;
+    int gpio = 0;
+    int initialized = 0;
+    int iscpro = 0;
 
+    // Figure out if we are a CPro
+    iscpro = is_this_chippro();
+
+    // Figure out which pin we are
+    if (strcmp(key,"U13_18") == 0) {
+        gpio = 0;
+    } else if (strcmp(key,"EINT13") == 0) {
+        gpio = 1;
+    }
+
+    // Try to get the pwm
+    pwm = lookup_exported_pwm(key);
+
+    if (pwm == NULL) {
+        initialize_pwm(&initialized, gpio);
         if (DEBUG)
-        printf(" ** IN pwm_start: pwm_initialized = %d\n", pwm_initialized);
-    if(!pwm_initialized) {
-        initialize_pwm();
+            printf(" ** pwm_start: pwm(%d) initialized = %d\n", gpio, initialized);
     } else {
         if (DEBUG)
-            printf(" ** ALREADY INITIALIZED, CALLING CLEANUP TO START FRESH **");
+            printf(" ** pwm_start: pwm(%d) already initialized, cleaning up **", gpio);
         pwm_cleanup();   
     }
-    if (DEBUG)
-        printf(" ** IN pwm_start: pwm_initialized = %d\n", pwm_initialized);
 
     //setup the pwm base path, the chip only has one pwm
-    snprintf(pwm_base_path, sizeof(pwm_base_path), "/sys/class/pwm/pwmchip0/pwm%d", 0); BUF2SMALL(pwm_base_path);
+    snprintf(pwm_base_path, sizeof(pwm_base_path), "/sys/class/pwm/pwmchip0/pwm%d", gpio); BUF2SMALL(pwm_base_path);
 
     //create the path for the period and duty
     snprintf(enable_path, sizeof(enable_path), "%s/enable", pwm_base_path); BUF2SMALL(enable_path);
@@ -332,19 +450,26 @@ int pwm_start(const char *key, float duty, float freq, int polarity)
     snprintf(polarity_path, sizeof(polarity_path), "%s/polarity", pwm_base_path); BUF2SMALL(polarity_path);
 
     if (DEBUG) {
-        printf(" ** IN pwm_start: pwm_base_path: %s\n", pwm_base_path);
-        printf(" ** IN pwm_start: enable_path:   %s\n", enable_path);
-        printf(" ** IN pwm_start: period_path:   %s\n", period_path);
-        printf(" ** IN pwm_start: duty_path:     %s\n", duty_path);
-        printf(" **IN pwm_start: polarity_path: %s\n", polarity_path);
+        printf(" ** pwm_start: pwm_base_path: %s\n", pwm_base_path);
+        printf(" ** pwm_start: enable_path:   %s\n", enable_path);
+        printf(" ** pwm_start: period_path:   %s\n", period_path);
+        printf(" ** pwm_start: duty_path:     %s\n", duty_path);
+        printf(" ** pwm_start: polarity_path: %s\n", polarity_path);
     }
     
     //add period and duty fd to pwm list
-    if ((enable_fd = open(enable_path, O_WRONLY)) < 0)
+    if ((enable_fd = open(enable_path, O_WRONLY)) < 0) {
+        char err[256];
+        snprintf(err, sizeof(err), "pwm_start: could not open enable file");
+        add_error_msg(err);
         return -1;
+    }
 
     if ((period_fd = open(period_path, O_WRONLY)) < 0) {
         close(enable_fd);
+        char err[256];
+        snprintf(err, sizeof(err), "pwm_start: could not open period file");
+        add_error_msg(err);
         return -1;
     }
 
@@ -352,6 +477,9 @@ int pwm_start(const char *key, float duty, float freq, int polarity)
         //error, close already opened period_fd.
         close(enable_fd);
         close(period_fd);
+        char err[256];
+        snprintf(err, sizeof(err), "pwm_start: could not open duty cycle file");
+        add_error_msg(err);
         return -1;
     }
 
@@ -360,19 +488,28 @@ int pwm_start(const char *key, float duty, float freq, int polarity)
         close(enable_fd);
         close(period_fd);
         close(duty_fd);
+        char err[256];
+        snprintf(err, sizeof(err), "pwm_start: could not open polarity file");
+        add_error_msg(err);
         return -1;
     }
 
     // add to list
     new_pwm = malloc(sizeof(struct pwm_exp));
     if (new_pwm == 0) {
-        return -1; // out of memory
+        char err[256];
+        snprintf(err, sizeof(err), "pwm_start: unable to allocate memory");
+        add_error_msg(err);
+        return -1;
     }
 
     if (DEBUG)
-        printf(" ** IN pwm_start: IF WE MAKE IT HERE, THE FILES WERE SUCCESSFULLY OPEN **\n");
+        printf(" ** pwm_start: sysfs files opened successfully **\n");
     strncpy(new_pwm->key, key, KEYLEN);  /* can leave string unterminated */
     new_pwm->key[KEYLEN] = '\0'; /* terminate string */
+    new_pwm->gpio = gpio;
+    new_pwm->iscpro = iscpro;
+    new_pwm->initialized = initialized;
     new_pwm->period_fd = period_fd;
     new_pwm->duty_fd = duty_fd;
     new_pwm->polarity_fd = polarity_fd;
@@ -392,14 +529,21 @@ int pwm_start(const char *key, float duty, float freq, int polarity)
     }
 
     int rtnval = 0;
+    // Fix for issue #53
+    // Always set polarity first
+    rtnval = pwm_set_polarity(key, polarity);
+    if (rtnval != -1) {
+        rtnval = 0;
         rtnval = pwm_set_enable(key, ENABLE);
+        if (rtnval != -1) {
             rtnval = 0;
             rtnval = pwm_set_frequency(key, freq);
+            if (rtnval != -1) {
                 rtnval = 0;
-    //rtnval = pwm_set_polarity(key, polarity);
-    //rtnval = 0;
                 rtnval = pwm_set_duty_cycle(key, duty);
-
+            }
+        }
+    }
     return rtnval;
 }
 
@@ -407,25 +551,39 @@ int pwm_disable(const char *key)
 {
     struct pwm_exp *pwm, *temp, *prev_pwm = NULL;
 
-    int fd, len;
+    int fd, len, e_no;
     char str_gpio[80];
-    // Per https://github.com/NextThingCo/CHIP-linux/pull/4
-    // we need to export 0 here to enable pwm0
-    int gpio = 0;
+
+    pwm = lookup_exported_pwm(key);
+
+    if (pwm == NULL) {
+        if (DEBUG)
+            printf(" ** pwm_disable: pwm struct is null **\n");
+        return -1;
+    }
 
     // Disable the PWM
     pwm_set_frequency(key, 0);
-    //pwm_set_polarity(key, 0);
     pwm_set_duty_cycle(key, 0);
     pwm_set_enable(key, DISABLE);
+    pwm_set_polarity(key, 0);
 
     if ((fd = open("/sys/class/pwm/pwmchip0/unexport", O_WRONLY)) < 0)
     {
+        char err[256];
+        snprintf(err, sizeof(err), "pwm_disable: could not open unexport file");
+        add_error_msg(err);
         return -1;
     }
-    len = snprintf(str_gpio, sizeof(str_gpio), "%d", gpio); BUF2SMALL(str_gpio);
-    ssize_t s = write(fd, str_gpio, len);  ASSRT(s == len);
+    len = snprintf(str_gpio, sizeof(str_gpio), "%d", pwm->gpio); BUF2SMALL(str_gpio);
+    ssize_t s = write(fd, str_gpio, len); e_no = errno;
     close(fd);
+    if (s != len) {
+        char err[256];
+        snprintf(err, sizeof(err), "pwm_disable: could not unexport pwm (%s)", strerror(e_no));
+        add_error_msg(err);
+        return -1;
+    }
     
     // remove from list
     pwm = exported_pwms;
@@ -433,6 +591,9 @@ int pwm_disable(const char *key)
     {
         if (strcmp(pwm->key, key) == 0)
         {
+            if (DEBUG) {
+                printf(" ** pwm_disable: freeing memory %s\n", key);
+            }
             //close the fd
             close(pwm->enable_fd);
             close(pwm->period_fd);
@@ -464,11 +625,3 @@ void pwm_cleanup(void)
     }
 }
 
-void pwm_toggle_debug(void)
-{
-    if (DEBUG) {
-        DEBUG = 0;
-    } else {
-        DEBUG = 1;
-    }
-}

source/c_pwm.h

@@ -32,7 +32,9 @@ SOFTWARE.
 int pwm_start(const char *key, float duty, float freq, int polarity);
 int pwm_disable(const char *key);
 int pwm_set_frequency(const char *key, float freq);
+int pwm_set_period_ns(const char *key, unsigned long period_ns);
+int pwm_get_period_ns(const char *key, unsigned long *period_ns);
 int pwm_set_duty_cycle(const char *key, float duty);
+int pwm_set_pulse_width_ns(const char *key, unsigned long pulse_width_ns);
 int pwm_set_enable(const char *key, int enable);
 void pwm_cleanup(void);
-void pwm_toggle_debug(void);

source/c_softpwm.c

@@ -35,10 +35,11 @@ SOFTWARE.
 #include <sys/types.h>
 #include <string.h>
 #include <fcntl.h>
+#include <errno.h>
 #include <unistd.h>
 #include <pthread.h>
 #include <time.h>
-#include "c_pwm.h"
+#include "c_softpwm.h"
 #include "common.h"
 #include "event_gpio.h"
 
@@ -96,6 +97,8 @@ int softpwm_set_frequency(const char *key, float freq) {
         return -1;
     }
 
+    if (DEBUG)
+        printf(" ** softpwm_set_frequency: %f **\n", freq);
     pthread_mutex_lock(pwm->params_lock);
     pwm->params.freq = freq;
     pthread_mutex_unlock(pwm->params_lock);
@@ -116,6 +119,8 @@ int softpwm_set_polarity(const char *key, int polarity) {
         return -1;
     }
 
+    if (DEBUG)
+        printf(" ** softpwm_set_polarity: %d **\n", polarity);
     pthread_mutex_lock(pwm->params_lock);
     pwm->params.polarity = polarity;
     pthread_mutex_unlock(pwm->params_lock);
@@ -135,6 +140,8 @@ int softpwm_set_duty_cycle(const char *key, float duty) {;
         return -1;
     }
 
+    if (DEBUG)
+        printf(" ** softpwm_set_duty_cycle: %f **\n", duty);
     pthread_mutex_lock(pwm->params_lock);
     pwm->params.duty = duty;
     pthread_mutex_unlock(pwm->params_lock);
@@ -194,7 +201,6 @@ void *softpwm_thread_toggle(void *arg)
 
     if (enabled_local)
     {
-
       /* Force 0 duty cycle to be 0 */
       if (duty_local != 0)
       {
@@ -238,16 +244,27 @@ int softpwm_start(const char *key, float duty, float freq, int polarity)
     int gpio;
     int ret;
 
-    if (get_gpio_number(key, &gpio) < 0)
+    if (get_gpio_number(key, &gpio) < 0) {
+        if (DEBUG)
+            printf(" ** softpwm_start: invalid gpio specified **\n");
         return -1;
+    }
+        
     if (gpio_export(gpio) < 0) {
        char err[2000];
        snprintf(err, sizeof(err), "Error setting up softpwm on pin %d, maybe already exported? (%s)", gpio, get_error_msg());
        add_error_msg(err);
        return -1;
     }
-    if (gpio_set_direction(gpio, OUTPUT) < 0)
+    
+    if (DEBUG)
+        printf(" ** softpwm_start: %d exported **\n", gpio);
+    
+    if (gpio_set_direction(gpio, OUTPUT) < 0) {
+        if (DEBUG)
+            printf(" ** softpwm_start: gpio_set_direction failed **\n");
         return -1;
+    }
 
     // add to list
     new_pwm = malloc(sizeof(struct softpwm));  ASSRT(new_pwm != NULL);
@@ -279,12 +296,16 @@ int softpwm_start(const char *key, float duty, float freq, int polarity)
     }
     pthread_mutex_unlock(new_params_lock);
 
+    if (DEBUG)
+        printf(" ** softpwm_enable: setting softpwm parameters **\n");
     ASSRT(softpwm_set_duty_cycle(new_pwm->key, duty) == 0);
     ASSRT(softpwm_set_frequency(new_pwm->key, freq) == 0);
     ASSRT(softpwm_set_polarity(new_pwm->key, polarity) == 0);
 
     pthread_mutex_lock(new_params_lock);
     // create thread for pwm
+    if (DEBUG)
+        printf(" ** softpwm_enable: creating thread **\n");
     ret = pthread_create(&new_thread, NULL, softpwm_thread_toggle, (void *)new_pwm);
     ASSRT(ret == 0);
 
@@ -299,17 +320,23 @@ int softpwm_disable(const char *key)
 {
     struct softpwm *pwm, *temp, *prev_pwm = NULL;
 
+    if (DEBUG)
+        printf(" ** in softpwm_disable **\n");
     // remove from list
     pwm = exported_pwms;
     while (pwm != NULL)
     {
         if (strcmp(pwm->key, key) == 0)
         {
+            if (DEBUG)
+                printf(" ** softpwm_disable: found pin **\n");
             pthread_mutex_lock(pwm->params_lock);
             pwm->params.stop_flag = true;
             pthread_mutex_unlock(pwm->params_lock);
             pthread_join(pwm->thread, NULL);  /* wait for thread to exit */
 
+            if (DEBUG)
+                printf(" ** softpwm_disable: unexporting %d **\n", pwm->gpio);
             gpio_unexport(pwm->gpio);
 
             if (prev_pwm == NULL)

source/c_softservo.c

@@ -0,0 +1,355 @@
+/*
+Copyright (c) 2017 Robert Wolterman
+
+Using CHIP_IO servo code from Brady Hurlburt as a basis for the servo code
+
+Copyright (c) 2016 Brady Hurlburt
+
+Original BBIO Author Justin Cooper
+Modified for CHIP_IO Author Brady Hurlburt
+
+This file incorporates work covered by the following copyright and
+permission notice, all modified code adopts the original license:
+
+Copyright (c) 2013 Adafruit
+Author: Justin Cooper
+
+Permission is hereby granted, free of charge, to any person obtaining a copy of
+this software and associated documentation files (the "Software"), to deal in
+the Software without restriction, including without limitation the rights to
+use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies
+of the Software, and to permit persons to whom the Software is furnished to do
+so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all
+copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+SOFTWARE.
+*/
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <stdbool.h>
+#include <sys/types.h>
+#include <string.h>
+#include <fcntl.h>
+#include <errno.h>
+#include <unistd.h>
+#include <pthread.h>
+#include <time.h>
+#include "c_softservo.h"
+#include "common.h"
+#include "event_gpio.h"
+
+#define KEYLEN 7
+
+#define PERIOD 0
+#define DUTY 1
+
+#define MSTONS 1000000
+#define BLOCKNS 20 * MSTONS
+#define FUDGEFACTOR 450
+#define MSTOMICROS 1000
+#define MICROSTONS 1000
+#define MINMICROS 1000
+#define NEUTRAL 1500
+#define MAXMICROS 2000
+
+int servo_initialized = 0;
+
+struct servo_params
+{
+    float range;
+    float min_angle;
+    float max_angle;
+    float current_angle;
+    bool enabled;
+    bool stop_flag;
+};
+
+struct servo
+{
+    char key[KEYLEN+1]; /* leave room for terminating NUL byte */
+    int gpio;
+    struct servo_params params;
+    pthread_mutex_t* params_lock;
+    pthread_t thread;
+    struct servo *next;
+};
+struct servo *exported_servos = NULL;
+
+struct servo *lookup_exported_servo(const char *key)
+{
+    struct servo *srv = exported_servos;
+
+    while (srv != NULL)
+    {
+        if (strcmp(srv->key, key) == 0) {
+            return srv;
+        }
+        srv = srv->next;
+    }
+
+    return NULL; /* standard for pointers */
+}
+
+void *servo_thread_toggle(void *arg)
+{
+    struct servo *srv = (struct servo *)arg;
+    int gpio = srv->gpio;
+    struct timespec tim_on;
+    struct timespec tim_off;
+    float on_time_microsec = 0;
+    unsigned int on_ns;
+    unsigned int off_ns;
+
+    /* Used to determine if something has
+     * has changed
+    */
+    float angle_local = 0;
+    float range_local = 0;
+    bool stop_flag_local = false;
+    bool enabled_local = false;
+    bool recalculate_timing = false;
+
+    while (!stop_flag_local) {
+        /* Take a snapshot of the parameter block */
+        pthread_mutex_lock(srv->params_lock);
+        if ((angle_local != srv->params.current_angle) || (range_local != srv->params.range)) {
+            recalculate_timing = true;
+        }
+        angle_local = srv->params.current_angle;
+        range_local = srv->params.range;
+        enabled_local = srv->params.enabled;
+        stop_flag_local = srv->params.stop_flag;
+        pthread_mutex_unlock(srv->params_lock);
+
+        /* If freq or duty has been changed, update the
+         * sleep times
+        */
+        if (recalculate_timing) {
+            if (DEBUG)
+                printf(" ** servo updating timing: new angle: (%.2f)\n",angle_local);
+            on_time_microsec = (((MAXMICROS - MINMICROS) / range_local) * angle_local) + NEUTRAL;
+            on_ns = (unsigned long)(on_time_microsec * MICROSTONS - FUDGEFACTOR);
+            off_ns = BLOCKNS - on_ns;
+            tim_on.tv_sec = 0;
+            tim_on.tv_nsec = on_ns;
+            tim_off.tv_sec = 0;
+            tim_off.tv_nsec = off_ns;
+            recalculate_timing = false;
+        }
+
+        if (enabled_local)
+        {
+            /* Set gpio */
+            gpio_set_value(gpio, HIGH);
+
+            nanosleep(&tim_on, NULL);
+
+            /* Unset gpio */
+            gpio_set_value(gpio, LOW);
+
+            nanosleep(&tim_off, NULL);
+            //printf("AFTER SECOND NANOSLEEP\n");
+        }  /* if enabled_local */
+    }  /* while !stop_flag_local */
+
+    gpio_set_value(gpio, LOW);
+
+    /* This servo has been disabled */
+    pthread_exit(NULL);
+}
+
+int servo_start(const char *key, float angle, float range)
+{
+    struct servo *new_srv, *srv;
+    pthread_t new_thread;
+    pthread_mutex_t *new_params_lock;
+    int gpio;
+    int ret;
+
+    if (get_gpio_number(key, &gpio) < 0) {
+        if (DEBUG)
+            printf(" ** servo_start: invalid gpio specified **\n");
+        return -1;
+    }
+    
+    if (gpio_export(gpio) < 0) {
+       char err[2000];
+       snprintf(err, sizeof(err), "Error setting up servo on pin %d, maybe already exported? (%s)", gpio, get_error_msg());
+       add_error_msg(err);
+       return -1;
+    }
+    
+    if (DEBUG)
+        printf(" ** servo_start: %d exported **\n", gpio);
+    
+    if (gpio_set_direction(gpio, OUTPUT) < 0) {
+        if (DEBUG)
+            printf(" ** servo_start: gpio_set_direction failed **\n");
+        return -1;
+    }
+
+    printf("c_softservo.c: servo_start(%d,%.2f,%.2f)\n",gpio,angle,range);
+    
+    // add to list
+    new_srv = malloc(sizeof(struct servo));  ASSRT(new_srv != NULL);
+    new_params_lock = (pthread_mutex_t *)malloc(sizeof(pthread_mutex_t));
+    if (new_srv == 0) {
+        return -1; // out of memory
+    }
+    pthread_mutex_init(new_params_lock, NULL);
+    pthread_mutex_lock(new_params_lock);
+
+    strncpy(new_srv->key, key, KEYLEN);  /* can leave string unterminated */
+    new_srv->key[KEYLEN] = '\0'; /* terminate string */
+    new_srv->gpio = gpio;
+    new_srv->params.enabled = true;
+    new_srv->params.stop_flag = false;
+    new_srv->params_lock = new_params_lock;
+    new_srv->next = NULL;
+
+    if (exported_servos == NULL)
+    {
+        // create new list
+        exported_servos = new_srv;
+    } else {
+        // add to end of existing list
+        srv = exported_servos;
+        while (srv->next != NULL)
+            srv = srv->next;
+        srv->next = new_srv;
+    }
+    pthread_mutex_unlock(new_params_lock);
+
+    if (DEBUG)
+        printf(" ** servo_enable: setting servo parameters **\n");
+    ASSRT(servo_set_range(new_srv->key, range) == 0);
+    ASSRT(servo_set_angle(new_srv->key, angle) == 0);
+
+    pthread_mutex_lock(new_params_lock);
+    // create thread for srv
+    if (DEBUG)
+        printf(" ** servo_enable: creating thread **\n");
+    ret = pthread_create(&new_thread, NULL, servo_thread_toggle, (void *)new_srv);
+    ASSRT(ret == 0);
+
+    new_srv->thread = new_thread;
+
+    pthread_mutex_unlock(new_params_lock);
+
+    return 1;
+}
+
+int servo_disable(const char *key)
+{
+    struct servo *srv, *temp, *prev_srv = NULL;
+
+    if (DEBUG)
+        printf(" ** in servo_disable **\n");
+    // remove from list
+    srv = exported_servos;
+    while (srv != NULL)
+    {
+        if (strcmp(srv->key, key) == 0)
+        {
+            if (DEBUG)
+                printf(" ** servo_disable: found pin **\n");
+            pthread_mutex_lock(srv->params_lock);
+            srv->params.stop_flag = true;
+            pthread_mutex_unlock(srv->params_lock);
+            pthread_join(srv->thread, NULL);  /* wait for thread to exit */
+
+            if (DEBUG)
+                printf(" ** servo_disable: unexporting %d **\n", srv->gpio);
+            gpio_unexport(srv->gpio);
+
+            if (prev_srv == NULL)
+            {
+                exported_servos = srv->next;
+                prev_srv = srv;
+            } else {
+                prev_srv->next = srv->next;
+            }
+
+            temp = srv;
+            srv = srv->next;
+            free(temp->params_lock);
+            free(temp);
+        } else {
+            prev_srv = srv;
+            srv = srv->next;
+        }
+    }
+    return 0;
+}
+
+int servo_set_range(const char *key, float range)
+{
+    struct servo *srv;
+    float min_angle, max_angle;
+
+    srv = lookup_exported_servo(key);
+
+    if (srv == NULL) {
+        return -1;
+    }
+
+    // Compute the min and max angle
+    max_angle = range / 2.0;
+    min_angle = -max_angle;
+
+    if (DEBUG)
+        printf(" ** servo_set_range(%d,%.2f = %.2f,%.2f)\n",srv->gpio,range,min_angle,max_angle);
+    pthread_mutex_lock(srv->params_lock);
+    srv->params.range = range;
+    srv->params.min_angle = min_angle;
+    srv->params.max_angle = max_angle;
+    pthread_mutex_unlock(srv->params_lock);
+
+    return 0;
+}
+
+int servo_set_angle(const char *key, float angle)
+{
+    struct servo *srv;
+
+    srv = lookup_exported_servo(key);
+
+    if (srv == NULL) {
+        return -1;
+    }
+
+    // Make sure we're between the range of allowable angles
+    if (angle < srv->params.min_angle || angle > srv->params.max_angle) {
+       char err[2000];
+       snprintf(err, sizeof(err), "Angle specified (%.2f) for pin %d, is outside allowable range (%.2f,%.2f)", angle, srv->gpio, srv->params.min_angle,srv->params.max_angle);
+       add_error_msg(err);
+       return -1;
+    }
+    
+    if (DEBUG)
+        printf(" ** servo_set_angle(%d,%.2f)\n",srv->gpio,angle);
+    pthread_mutex_lock(srv->params_lock);
+    srv->params.current_angle = angle;
+    pthread_mutex_unlock(srv->params_lock);
+
+    return 0;
+}
+
+void servo_cleanup(void)
+{
+    while (exported_servos != NULL) {
+        servo_disable(exported_servos->key);
+    }
+}
+
+
+

source/c_softservo.h

@@ -0,0 +1,40 @@
+/*
+Copyright (c) 2017 Robert Wolterman
+
+Using CHIP_IO SoftPWM code from Brady Hurlburt as a basis for the servo code
+
+Copyright (c) 2016 Brady Hurlburt
+
+Original BBIO Author Justin Cooper
+Modified for CHIP_IO Author Brady Hurlburt
+
+This file incorporates work covered by the following copyright and
+permission notice, all modified code adopts the original license:
+
+Copyright (c) 2013 Adafruit
+Author: Justin Cooper
+
+Permission is hereby granted, free of charge, to any person obtaining a copy of
+this software and associated documentation files (the "Software"), to deal in
+the Software without restriction, including without limitation the rights to
+use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies
+of the Software, and to permit persons to whom the Software is furnished to do
+so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all
+copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+SOFTWARE.
+*/
+
+int servo_start(const char *key, float angle, float range);
+int servo_disable(const char *key);
+int servo_set_range(const char *key, float range);
+int servo_set_angle(const char *key, float angle);
+void servo_cleanup(void);

source/common.c

@@ -45,95 +45,102 @@ SOFTWARE.
 #include <string.h>
 #include <sys/stat.h>
 #include <stdlib.h>
+#include <sys/sysinfo.h>
 
 int setup_error = 0;
 int module_setup = 0;
 
+// Library Debug
+int DEBUG = 0;
+
+// Is This a CHIP PRO
+int is_chip_pro = 0;
+
 pins_t pins_info[] = {
-  { "GND",       "GND",         "U13_1",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CHG-IN",    "CHG-IN",      "U13_2",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "VCC-5V",    "VCC-5V",      "U13_3",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "GND",       "GND",         "U13_4",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "VCC-3V3",   "VCC-3V3",     "U13_5",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "TS",        "TS",          "U13_6",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "VCC-1V8",   "VCC-1V8",     "U13_7",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "BAT",       "BAT",         "U13_8",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "TWI1-SDA",  "KPD-I2C-SDA", "U13_9",   48, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "PWRON",     "PWRON",       "U13_10",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "TWI1-SCK",  "KPD-I2C-SCL", "U13_11",  47, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "GND",       "GND",         "U13_12",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "X1",        "X1",          "U13_13",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "X2",        "X2",          "U13_14",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "Y1",        "Y1",          "U13_15",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "Y2",        "Y2",          "U13_16",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D2",    "LCD-D2",      "U13_17",  98, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "PWM0",      "PWM0",        "U13_18",  34, BASE_METHOD_AS_IS,  0, -1, SPWM_DISABLED},
-  { "LCD-D4",    "LCD-D4",      "U13_19", 100, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D3",    "LCD-D3",      "U13_20",  99, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D6",    "LCD-D6",      "U13_21", 102, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D5",    "LCD-D5",      "U13_22", 101, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D10",   "LCD-D10",     "U13_23", 106, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D7",    "LCD-D7",      "U13_24", 103, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D12",   "LCD-D12",     "U13_25", 108, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D11",   "LCD-D11",     "U13_26", 107, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D14",   "LCD-D14",     "U13_27", 110, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D13",   "LCD-D13",     "U13_28", 109, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D18",   "LCD-D18",     "U13_29", 114, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D15",   "LCD-D15",     "U13_30", 111, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D20",   "LCD-D20",     "U13_31", 116, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D19",   "LCD-D19",     "U13_32", 115, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D22",   "LCD-D22",     "U13_33", 118, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D21",   "LCD-D21",     "U13_34", 117, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-CLK",   "LCD-CLK",     "U13_35", 120, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-D23",   "LCD-D23",     "U13_36", 119, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-VSYNC", "LCD-VSYNC",   "U13_37", 123, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-HSYNC", "LCD-HSYNC",   "U13_38", 122, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "GND",       "GND",         "U13_39",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LCD-DE",    "LCD-DE",      "U13_40", 121, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "GND",       "GND",         "U14_1",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "VCC-5V",    "VCC-5V",      "U14_2",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "UART1-TX",  "UART-TX",     "U14_3",  195, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "HPL",       "HPL",         "U14_4",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "UART1-RX",  "UART-RX",     "U14_5",  196, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "HPCOM",     "HPCOM",       "U14_6",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "FEL",       "FEL",         "U14_7",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "HPR",       "HPR",         "U14_8",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "VCC-3V3",   "VCC-3V3",     "U14_9",   -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "MICM",      "MICM",        "U14_10",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "LRADC",     "ADC",         "U14_11",  -1, BASE_METHOD_AS_IS, -1,  0, SPWM_DISABLED},
-  { "MICIN1",    "MICIN1",      "U14_12",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "XIO-P0",    "XIO-P0",      "U14_13",   0, BASE_METHOD_XIO,   -1, -1, SPWM_ENABLED},
-  { "XIO-P1",    "XIO-P1",      "U14_14",   1, BASE_METHOD_XIO,   -1, -1, SPWM_ENABLED},
-  { "XIO-P2",    "GPIO1",       "U14_15",   2, BASE_METHOD_XIO,   -1, -1, SPWM_ENABLED},
-  { "XIO-P3",    "GPIO2",       "U14_16",   3, BASE_METHOD_XIO,   -1, -1, SPWM_ENABLED},
-  { "XIO-P4",    "GPIO3",       "U14_17",   4, BASE_METHOD_XIO,   -1, -1, SPWM_ENABLED},
-  { "XIO-P5",    "GPIO4",       "U14_18",   5, BASE_METHOD_XIO,   -1, -1, SPWM_ENABLED},
-  { "XIO-P6",    "GPIO5",       "U14_19",   6, BASE_METHOD_XIO,   -1, -1, SPWM_ENABLED},
-  { "XIO-P7",    "GPIO6",       "U14_20",   7, BASE_METHOD_XIO,   -1, -1, SPWM_ENABLED},
-  { "GND",       "GND",         "U14_21",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "GND",       "GND",         "U14_22",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "AP-EINT1",  "KPD-INT",     "U14_23", 193, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "AP-EINT3",  "AP-INT3",     "U14_24",  35, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "TWI2-SDA",  "I2C-SDA",     "U14_25",  50, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "TWI2-SCK",  "I2C-SCL",     "U14_26",  49, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CSIPCK",    "SPI-SEL",     "U14_27", 128, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CSICK",     "SPI-CLK",     "U14_28", 129, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CSIHSYNC",  "SPI-MOSI",    "U14_29", 130, BASE_METHOD_AS_IS,  1, -1, SPWM_DISABLED},
-  { "CSIVSYNC",  "SPI-MISO",    "U14_30", 131, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CSID0",     "CSID0",       "U14_31", 132, BASE_METHOD_AS_IS,  1, -1, SPWM_DISABLED},
-  { "CSID1",     "CSID1",       "U14_32", 133, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CSID2",     "CSID2",       "U14_33", 134, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CSID3",     "CSID3",       "U14_34", 135, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CSID4",     "CSID4",       "U14_35", 136, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CSID5",     "CSID5",       "U14_36", 137, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CSID6",     "CSID6",       "U14_37", 138, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "CSID7",     "CSID7",       "U14_38", 139, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "GND",       "GND",         "U14_39",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
-  { "GND",       "GND",         "U14_40",  -1, BASE_METHOD_AS_IS, -1, -1, SPWM_DISABLED},
+  { "GND",       "GND",         "U13_1",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CHG-IN",    "CHG-IN",      "U13_2",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "VCC-5V",    "VCC-5V",      "U13_3",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "GND",       "GND",         "U13_4",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "VCC-3V3",   "VCC-3V3",     "U13_5",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "TS",        "TS",          "U13_6",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "VCC-1V8",   "VCC-1V8",     "U13_7",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "BAT",       "BAT",         "U13_8",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "TWI1-SDA",  "KPD-I2C-SDA", "U13_9",   48, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "PWRON",     "PWRON",       "U13_10",  -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "TWI1-SCK",  "KPD-I2C-SCL", "U13_11",  47, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "GND",       "GND",         "U13_12",  -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "X1",        "X1",          "U13_13",  -1, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "X2",        "X2",          "U13_14",  -1, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "Y1",        "Y1",          "U13_15",  -1, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "Y2",        "Y2",          "U13_16",  -1, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D2",    "UART2-TX",    "U13_17",  98, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "PWM0",      "PWM0",        "U13_18",  34, BASE_METHOD_AS_IS,  0, -1, BOTH},
+  { "PWM1",      "PWM1",        "EINT13", 205, BASE_METHOD_AS_IS,  0, -1, CHIPPRO},
+  { "LCD-D4",    "UART2-CTS",   "U13_19", 100, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "LCD-D3",    "UART2-RX",    "U13_20",  99, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "LCD-D6",    "LCD-D6",      "U13_21", 102, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D5",    "UART2-RTS",   "U13_22", 101, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "LCD-D10",   "LCD-D10",     "U13_23", 106, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D7",    "LCD-D7",      "U13_24", 103, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D12",   "LCD-D12",     "U13_25", 108, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D11",   "LCD-D11",     "U13_26", 107, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D14",   "LCD-D14",     "U13_27", 110, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D13",   "LCD-D13",     "U13_28", 109, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D18",   "LCD-D18",     "U13_29", 114, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D15",   "LCD-D15",     "U13_30", 111, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D20",   "LCD-D20",     "U13_31", 116, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D19",   "LCD-D19",     "U13_32", 115, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D22",   "LCD-D22",     "U13_33", 118, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D21",   "LCD-D21",     "U13_34", 117, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-CLK",   "LCD-CLK",     "U13_35", 120, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-D23",   "LCD-D23",     "U13_36", 119, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-VSYNC", "LCD-VSYNC",   "U13_37", 123, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "LCD-HSYNC", "LCD-HSYNC",   "U13_38", 122, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "GND",       "GND",         "U13_39",  -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "LCD-DE",    "LCD-DE",      "U13_40", 121, BASE_METHOD_AS_IS, -1, -1, CHIP},
+  { "GND",       "GND",         "U14_1",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "VCC-5V",    "VCC-5V",      "U14_2",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "UART1-TX",  "UART-TX",     "U14_3",  195, BASE_METHOD_AS_IS, -1, -1, BOTH}, /* THIS IS AP-EINT3 ON CHIP PRO */
+  { "HPL",       "HPL",         "U14_4",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "UART1-RX",  "UART-RX",     "U14_5",  196, BASE_METHOD_AS_IS, -1, -1, BOTH}, /* THIS IS AP-EINT4 ON CHIP PRO */
+  { "HPCOM",     "HPCOM",       "U14_6",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "FEL",       "FEL",         "U14_7",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "HPR",       "HPR",         "U14_8",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "VCC-3V3",   "VCC-3V3",     "U14_9",   -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "MICM",      "MICM",        "U14_10",  -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "LRADC",     "ADC",         "U14_11",  -1, BASE_METHOD_AS_IS, -1,  0, BOTH},
+  { "MICIN1",    "MICIN1",      "U14_12",  -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "XIO-P0",    "XIO-P0",      "U14_13",   0, BASE_METHOD_XIO,   -1, -1, CHIP},
+  { "XIO-P1",    "XIO-P1",      "U14_14",   1, BASE_METHOD_XIO,   -1, -1, CHIP},
+  { "XIO-P2",    "GPIO1",       "U14_15",   2, BASE_METHOD_XIO,   -1, -1, CHIP},
+  { "XIO-P3",    "GPIO2",       "U14_16",   3, BASE_METHOD_XIO,   -1, -1, CHIP},
+  { "XIO-P4",    "GPIO3",       "U14_17",   4, BASE_METHOD_XIO,   -1, -1, CHIP},
+  { "XIO-P5",    "GPIO4",       "U14_18",   5, BASE_METHOD_XIO,   -1, -1, CHIP},
+  { "XIO-P6",    "GPIO5",       "U14_19",   6, BASE_METHOD_XIO,   -1, -1, CHIP},
+  { "XIO-P7",    "GPIO6",       "U14_20",   7, BASE_METHOD_XIO,   -1, -1, CHIP},
+  { "GND",       "GND",         "U14_21",  -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "GND",       "GND",         "U14_22",  -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "AP-EINT1",  "KPD-INT",     "U14_23", 193, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "AP-EINT3",  "AP-INT3",     "U14_24",  35, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "TWI2-SDA",  "I2C-SDA",     "U14_25",  50, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "TWI2-SCK",  "I2C-SCL",     "U14_26",  49, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CSIPCK",    "SPI-SEL",     "U14_27", 128, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CSICK",     "SPI-CLK",     "U14_28", 129, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CSIHSYNC",  "SPI-MOSI",    "U14_29", 130, BASE_METHOD_AS_IS,  1, -1, BOTH},
+  { "CSIVSYNC",  "SPI-MISO",    "U14_30", 131, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CSID0",     "D0",          "U14_31", 132, BASE_METHOD_AS_IS,  1, -1, BOTH},
+  { "CSID1",     "D1",          "U14_32", 133, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CSID2",     "D2",          "U14_33", 134, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CSID3",     "D3",          "U14_34", 135, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CSID4",     "D4",          "U14_35", 136, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CSID5",     "D5",          "U14_36", 137, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CSID6",     "D6",          "U14_37", 138, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "CSID7",     "D7",          "U14_38", 139, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "GND",       "GND",         "U14_39",  -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
+  { "GND",       "GND",         "U14_40",  -1, BASE_METHOD_AS_IS, -1, -1, BOTH},
   { NULL,        NULL,          NULL,      -1, 0,                 -1, -1, -1}
 };
 
-
 // CREDIT FOR THIS FUNCTION DUE TO HOWIE KATZ OF NTC AND STEVE FORD
 // THIS WILL FIND THE PROPER XIO BASE SYSFS NUMBER
 // PORTED TO C FORM HOWIE'S PYTHON CODE WITH THE HELP OF STEVE:
@@ -214,6 +221,109 @@ int get_xio_base(void)
   return xio_base_address; 
 }  /* get_xio_base */
 
+#define RAMDETERMINER 380.0
+
+int is_this_chippro(void)
+{
+    int is_pro = 0;
+    struct sysinfo si;
+    sysinfo (&si);
+    const double megabyte = 1024 * 1024;
+    
+    if (DEBUG)
+        printf(" ** is_this_chippro: total system ram: %5.1f mb\n", si.totalram / megabyte);
+    
+    if ((si.totalram/megabyte) > RAMDETERMINER) {
+        is_pro = 0;
+        if (DEBUG)
+            printf(" ** is_this_chippro: we are a chip\n");
+    } else {
+        is_pro = 1;
+        if (DEBUG)
+            printf(" ** is_this_chippro: we are a chip pro\n");
+    }
+    
+    return is_pro;
+}
+
+int gpio_allowed(int gpio)
+{
+    int rtnval = -1;
+    pins_t *p;
+    int tmpgpio = -1;
+    
+    // If the return is good, we should be good to go, so let's check the data
+
+    // Loop through the pins
+    for (p = pins_info; p->key != NULL; ++p) {
+        tmpgpio = gpio_number(p);
+        if (tmpgpio == gpio) {
+            if (DEBUG)
+                printf(" ** gpio_allowed: found match\n");
+            // We have a CHIP and the pin is for CHIP/BOTH
+            if (((p->sbc_type == CHIP) || (p->sbc_type == BOTH)) && (is_this_chippro() == 0)) {
+                if (DEBUG)
+                    printf(" ** gpio_allowed: pin allowed for chip or both and we're a chip\n");
+                rtnval = 1;
+            // We have a CHIP Pro and the pin is for CHIPPRO/BOTH
+            } else if (((p->sbc_type == CHIPPRO) || (p->sbc_type == BOTH)) && (is_this_chippro() == 1)) {
+                if (DEBUG)
+                    printf(" ** gpio_allowed: pin allowed for chip pro or both and we're a chip pro\n");
+                rtnval = 1;
+            } else {
+                if (DEBUG)
+                    printf(" ** gpio_allowed: pin is not allowed on hardware\n");
+                rtnval = 0;
+            }
+        }
+    }
+
+    return rtnval;
+}
+
+int pwm_allowed(const char *key)
+{
+    int rtnval = -1;
+    pins_t *p;
+    // Determine if we are CHIP Pro
+    // Running because we cannot be sure if it was previously run
+    
+    // If the return is good, we should be good to go, so let's check the data
+    for (p = pins_info; p->key != NULL; ++p) {
+        if (strcmp(p->key, key) == 0) {
+            if (DEBUG)
+                printf(" ** pwm_allowed: found match\n");
+            // We have a CHIP and the pin is for CHIP/BOTH
+            if ((p->sbc_type == BOTH) && (is_this_chippro() == 0)) {
+                if (DEBUG)
+                    printf(" ** pwm_allowed: pwm allowed for chip or both and we're a chip\n");
+                rtnval = 1;
+            // We have a CHIP Pro and the pin is for CHIPPRO/BOTH
+            } else if (((p->sbc_type == CHIPPRO) || (p->sbc_type == BOTH)) && (is_this_chippro() == 1)) {
+                if (DEBUG)
+                    printf(" ** pwm_allowed: pwm allowed for chip pro or both and we're a chip pro\n");
+                rtnval = 1;
+            } else {
+                if (DEBUG)
+                    printf(" ** pwm_allowed: pwm is not allowed on hardware\n");
+                rtnval = 0;
+            }
+        }
+    }
+
+    return rtnval;
+}
+
+void toggle_debug(void)
+{
+    if (DEBUG) {
+        DEBUG = 0;
+        printf(" ** debug disabled\n");
+    } else {
+        DEBUG = 1;
+        printf(" ** debug enabled\n");
+    }
+}
 
 int gpio_number(pins_t *pin)
 {
@@ -239,6 +349,22 @@ int gpio_number(pins_t *pin)
   return gpio_num;
 }  /* gpio_number */
 
+int gpio_pud_capable(pins_t *pin)
+{
+  int capable = -1;
+
+  switch (pin->base_method) {
+    case BASE_METHOD_AS_IS:
+      capable = 1;
+      break;
+    
+    case BASE_METHOD_XIO:
+      capable = 0;
+      break;
+  }
+
+  return capable;
+}
 
 int lookup_gpio_by_key(const char *key)
 {
@@ -273,6 +399,39 @@ int lookup_gpio_by_altname(const char *altname)
   return -1;
 }
 
+int lookup_pud_capable_by_key(const char *key)
+{
+  pins_t *p;
+  for (p = pins_info; p->key != NULL; ++p) {
+      if (strcmp(p->key, key) == 0) {
+          return gpio_pud_capable(p);
+      }
+  }
+  return -1;
+}
+
+int lookup_pud_capable_by_name(const char *name)
+{
+  pins_t *p;
+  for (p = pins_info; p->name != NULL; ++p) {
+      if (strcmp(p->name, name) == 0) {
+          return gpio_pud_capable(p);
+      }
+  }
+  return -1;
+}
+
+int lookup_pud_capable_by_altname(const char *altname)
+{
+  pins_t *p;
+  for (p = pins_info; p->altname != NULL; ++p) {
+      if (strcmp(p->altname, altname) == 0) {
+          return gpio_pud_capable(p);
+      }
+  }
+  return -1;
+}
+
 int lookup_ain_by_key(const char *key)
 {
   pins_t *p;
@@ -351,12 +510,16 @@ int get_pwm_key_by_name(const char *name, char *key)
     pins_t *p;
     for (p = pins_info; p->name != NULL; ++p) {
         if (strcmp(p->name, name) == 0) {
-            printf("## FOUND PWM KEY, VALIDATING MUX MODE ##\n");
+            if (DEBUG) {
+                printf(" ** get_pwm_key_by_name: FOUND PWM KEY, VALIDATING MUX MODE **\n");
+            }
             //validate it's a valid pwm pin
             if (p->pwm_mux_mode == -1)
                 return 0;
 
-            printf("## PWM KEY IS VALID ##\n");
+            if (DEBUG) {
+                printf(" ** get_pwm_key_by_name: PWM KEY IS VALID ##\n");
+            }
             strncpy(key, p->key, 7);
             key[7] = '\0';
             return 1;
@@ -382,6 +545,33 @@ int get_gpio_number(const char *key, int *gpio)
     return status;
 }
 
+int compute_port_pin(const char *key, int gpio, int *port, int *pin)
+{
+    int capable = 0;
+    int rtn = -1;
+
+    capable = lookup_pud_capable_by_key(key);
+    if (capable < 0) {
+        capable = lookup_pud_capable_by_name(key);
+        if (capable < 0) {
+             capable = lookup_pud_capable_by_altname(key);
+             if (capable < 0) {
+                 capable = 0;  // default to false
+             }
+        }
+    }
+
+    if (capable) {
+        // Method from:
+        // https://bbs.nextthing.co/t/chippy-gonzales-fast-gpio/14056/6?u=xtacocorex
+        *port = gpio / 32;
+        *pin = gpio % 32;
+        rtn = 0;
+    }
+    
+    return rtn;
+}
+
 int get_key(const char *input, char *key)
 {
     if (!copy_key_by_key(input, key)) {
@@ -440,33 +630,6 @@ int build_path(const char *partial_path, const char *prefix, char *full_path, si
     return 0;
 }
 
-int get_spi_bus_path_number(unsigned int spi)
-{
-  char path[FILENAME_BUFFER_SIZE];
-  char ocp_dir[FILENAME_BUFFER_SIZE];
-
-  build_path("/sys/devices", "ocp", ocp_dir, sizeof(ocp_dir)); BUF2SMALL(ocp_dir);
-
-  if (spi == 0) {
-    snprintf(path, sizeof(path), "%s/48030000.spi/spi_master/spi1", ocp_dir); BUF2SMALL(path);
-  } else {
-    snprintf(path, sizeof(path), "%s/481a0000.spi/spi_master/spi1", ocp_dir); BUF2SMALL(path);
-  }
-
-  DIR* dir = opendir(path);
-  if (dir) {
-    closedir(dir);
-    //device is using /dev/spidev1.x
-    return 1;
-  } else if (ENOENT == errno) {
-    //device is using /dev/spidev2.x
-    return 2;
-  } else {
-    return -1;
-  }
-}
-
-
 // We do not know at compile time how many GPIOs there are, so it is not safe
 // to declare per-GPIO arrays with a static size.  The "dyn_int_array_*"
 // functions implement a dynamic integer array which grows as needed at run

source/common.h

@@ -52,8 +52,11 @@ SOFTWARE.
 } while (0)
 
 #define MODE_UNKNOWN -1
+#define BOARD        10
+#define BCM          11
 #define CHIP         0
 #define CHIPPRO      1
+#define BOTH         2
 
 // In the pins_t structure, the "base_method" field tells how
 // the "gpio" field should be interpreted.
@@ -66,11 +69,12 @@ typedef struct pins_t {
     const char *name;
     const char *altname; /* alternate name as referenced on pocketchip pin header */
     const char *key;
+    //const char *altkey; /* alternate key for chip pro */
     int gpio;           /* port number to use under /sys/class/gpio */
     int base_method;    /* modifier for port number; see BASE_METHOD_... */
     int pwm_mux_mode;   /* pwm pin */
     int ain;            /* analog pin */
-    int spwm_allow;     /* pin allowed for software pwm */
+    int sbc_type;     /* which sbc pin is allowed */
 } pins_t;
 
 
@@ -84,12 +88,18 @@ typedef struct dyn_int_array_s dyn_int_array_t;
 
 int setup_error;
 int module_setup;
+int DEBUG;
 
 int get_xio_base(void);
+int is_this_chippro(void);
 int gpio_number(pins_t *pin);
+int gpio_pud_capable(pins_t *pin);
 int lookup_gpio_by_key(const char *key);
 int lookup_gpio_by_name(const char *name);
 int lookup_gpio_by_altname(const char *altname);
+int lookup_pud_capable_by_key(const char *key);
+int lookup_pud_capable_by_name(const char *name);
+int lookup_pud_capable_by_altname(const char *altname);
 int lookup_ain_by_key(const char *key);
 int lookup_ain_by_name(const char *name);
 int copy_key_by_key(const char *input_key, char *key);
@@ -101,10 +111,13 @@ int get_key(const char *input, char *key);
 int get_pwm_key(const char *input, char *key);
 int get_adc_ain(const char *key, unsigned int *ain);
 int build_path(const char *partial_path, const char *prefix, char *full_path, size_t full_path_len);
-int get_spi_bus_path_number(unsigned int spi);
 void dyn_int_array_set(dyn_int_array_t **in_array, int i, int val, int initial_val);
 int dyn_int_array_get(dyn_int_array_t **in_array, int i, int initial_val);
 void dyn_int_array_delete(dyn_int_array_t **in_array);
 void clear_error_msg(void);
 char *get_error_msg(void);
 void add_error_msg(char *msg);
+void toggle_debug(void);
+int compute_port_pin(const char *key, int gpio, int *port, int *pin);
+int gpio_allowed(int gpio);
+int pwm_allowed(const char *key);

source/constants.c

@@ -76,6 +76,15 @@ void define_constants(PyObject *module)
    both_edge = Py_BuildValue("i", BOTH_EDGE);
    PyModule_AddObject(module, "BOTH", both_edge);
 
-   version = Py_BuildValue("s", "0.2.7");
+   unknown = Py_BuildValue("i", MODE_UNKNOWN);
+   PyModule_AddObject(module, "UNKNOWN", unknown);
+
+   board = Py_BuildValue("i", BOARD);
+   PyModule_AddObject(module, "BOARD", board);
+
+   bcm = Py_BuildValue("i", BCM);
+   PyModule_AddObject(module, "BCM", bcm);
+
+   version = Py_BuildValue("s", "0.5.5");
    PyModule_AddObject(module, "VERSION", version);
 }

source/constants.h

@@ -10,5 +10,8 @@ PyObject *rising_edge;
 PyObject *falling_edge;
 PyObject *both_edge;
 PyObject *version;
+PyObject *unknown;
+PyObject *board;
+PyObject *bcm;
 
 void define_constants(PyObject *module);

source/event_gpio.c

@@ -38,17 +38,23 @@ SOFTWARE.
 
 #include <pthread.h>
 #include <sys/epoll.h>
+#include <sys/mman.h>
 #include <stdio.h>
 #include <stdlib.h>
 #include <fcntl.h>
 #include <unistd.h>
 #include <errno.h>
 #include <string.h>
+#include <unistd.h>
+#include <stdint.h>
 #include "event_gpio.h"
 #include "common.h"
 
 const char *stredge[4] = {"none", "rising", "falling", "both"};
 
+// Memory Map for PUD
+uint8_t *memmap;
+
 // file descriptors
 struct fdx
 {
@@ -85,6 +91,63 @@ dyn_int_array_t *event_occurred = NULL;
 int thread_running = 0;
 int epfd = -1;
 
+// Thanks to WereCatf and Chippy-Gonzales for the Memory Mapping code/help
+int map_pio_memory()
+{
+    if (DEBUG)
+        printf(" ** map_pio_memory: opening /dev/mem **\n");
+    int fd = open("/dev/mem", O_RDWR|O_SYNC);
+	if(fd < 0) {
+        char err[256];
+        snprintf(err, sizeof(err), "map_pio_memory: could not open /dev/mem (%s)", strerror(errno));
+        add_error_msg(err);
+        return -1;
+	}
+	// uint32_t addr = 0x01c20800 & ~(getpagesize() - 1);
+	//Requires memmap to be on pagesize-boundary
+	if (DEBUG)
+        printf(" ** map_pio_memory: mapping memory **\n");
+	memmap = (uint8_t *)mmap(NULL, getpagesize()*2, PROT_READ|PROT_WRITE, MAP_SHARED, fd, 0x01C20000);
+	if(memmap == NULL) {
+        char err[256];
+        snprintf(err, sizeof(err), "map_pio_memory: mmap failed (%s)", strerror(errno));
+        add_error_msg(err);
+        return -1;
+	}
+	close(fd);
+
+	//Set memmap to point to PIO-registers
+	if (DEBUG)
+        printf(" ** map_pio_memory: moving to pio registers **\n");
+	memmap=memmap+0x800;
+	
+	return 0;
+}
+
+int gpio_get_pud(int port, int pin)
+{
+	if (DEBUG)
+        printf(" ** gpio_get_pud: port %d, pin %d **\n", port, pin);
+	volatile uint32_t *pioMem32, *configRegister;
+	pioMem32=(uint32_t *)(memmap+port*0x24+0x1c); //0x1c == pull-register
+	configRegister=pioMem32+(pin >> 4);
+	return *configRegister >> ((pin & 15) * 2) & 3;
+}
+
+int gpio_set_pud(int port, int pin, uint8_t value)
+{
+	if (DEBUG)
+        printf(" ** gpio_set_pud: port %d, pin %d, value %d **\n", port, pin, value);
+	value &= 3;
+	volatile uint32_t *pioMem32, *configRegister;
+	uint32_t mask;
+	pioMem32=(uint32_t *)(memmap+port*0x24+0x1c); //0x1c == pull-register
+	configRegister=pioMem32+(pin >> 4);
+	mask = ~(3 << ((pin & 15) * 2));
+	*configRegister &= mask;
+	*configRegister |= value << ((pin & 15) * 2);
+	return 0;
+}
 
 int gpio_export(int gpio)
 {
@@ -93,6 +156,9 @@ int gpio_export(int gpio)
     char str_gpio[80];
     struct gpio_exp *new_gpio, *g;
 
+    if (DEBUG)
+        printf(" ** gpio_export **\n");
+
     snprintf(filename, sizeof(filename), "/sys/class/gpio/export"); BUF2SMALL(filename);
 
     if ((fd = open(filename, O_WRONLY)) < 0)
@@ -115,6 +181,8 @@ int gpio_export(int gpio)
     }
 
     // add to list
+    if (DEBUG)
+        printf(" ** gpio_export: creating data struct **\n");
     new_gpio = malloc(sizeof(struct gpio_exp));  ASSRT(new_gpio != NULL);
 
     new_gpio->gpio = gpio;
@@ -217,6 +285,8 @@ int open_value_file(int gpio)
 
     // Changed this to open Read/Write to prevent a ton of file open/closes from happening when using
     // the GPIO for SOFTPWM
+    if (DEBUG)
+        printf(" ** open_value_file **\n");
     if ((fd = open(filename, O_RDWR | O_NONBLOCK)) < 0) {
         char err[256];
         snprintf(err, sizeof(err), "open_value_file: could not open '%s' (%s)", filename, strerror(errno));
@@ -236,6 +306,8 @@ int open_edge_file(int gpio)
     // create file descriptor of value file
     snprintf(filename, sizeof(filename), "/sys/class/gpio/gpio%d/edge", gpio); BUF2SMALL(filename);
 
+    if (DEBUG)
+        printf(" ** open_edge_file **\n");
     if ((fd = open(filename, O_RDONLY | O_NONBLOCK)) < 0) {
         char err[256];
         snprintf(err, sizeof(err), "open_edge_file: could not open '%s' (%s)", filename, strerror(errno));
@@ -253,6 +325,9 @@ int gpio_unexport(int gpio)
     char str_gpio[16];
     struct gpio_exp *g, *temp, *prev_g = NULL;
 
+    if (DEBUG)
+        printf(" ** gpio_unexport **\n");
+
     close_value_fd(gpio);
 
     snprintf(filename, sizeof(filename), "/sys/class/gpio/unexport"); BUF2SMALL(filename);
@@ -274,6 +349,8 @@ int gpio_unexport(int gpio)
         return -1;
     }
 
+    if (DEBUG)
+        printf(" ** gpio_unexport: freeing memory **\n");
     // remove from list
     g = exported_gpios;
     while (g != NULL)
@@ -315,6 +392,9 @@ int gpio_set_direction(int gpio, unsigned int in_flag)
     } else {
         strncpy(direction, "in", ARRAY_SIZE(direction) - 1);
     }
+    if (DEBUG)
+        printf(" ** gpio_set_direction: %s **\n",direction);
+    
     ssize_t s = write(fd, direction, strlen(direction));  e_no = errno;
     close(fd);
     if (s != strlen(direction)) {
@@ -361,6 +441,9 @@ int gpio_get_direction(int gpio, unsigned int *value)
         return -1;
     }
     
+    if (DEBUG)
+        printf(" ** gpio_get_direction: %s **\n",direction);
+
     if (strcmp(direction, "out") == 0)
         *value = OUTPUT;
     else if (strcmp(direction, "in") == 0)
@@ -403,6 +486,9 @@ int gpio_set_value(int gpio, unsigned int value)
         strncpy(vstr, "0", ARRAY_SIZE(vstr) - 1);
     }
 
+    //if (DEBUG)
+    //    printf(" ** gpio_set_value: writing %s **\n", vstr);
+
     ssize_t s = write(fd, vstr, strlen(vstr));  e_no = errno;
 
     if (s != strlen(vstr)) {
@@ -420,8 +506,7 @@ int gpio_get_value(int gpio, unsigned int *value)
     int fd = fd_lookup(gpio);
     char ch;
 
-    if (!fd)
-    {
+    if (!fd) {
         if ((fd = open_value_file(gpio)) == -1) {
             char err[256];
             snprintf(err, sizeof(err), "gpio_get_value: could not open GPIO %d value file", gpio);
@@ -444,6 +529,9 @@ int gpio_get_value(int gpio, unsigned int *value)
         return -1;
     }
 
+    if (DEBUG)
+        printf(" ** gpio_get_value: %c **\n", ch);
+
     if (ch == '1') {
         *value = 1;
     } else if (ch == '0') {
@@ -458,6 +546,58 @@ int gpio_get_value(int gpio, unsigned int *value)
     return 0;
 }
 
+int gpio_get_more(int gpio, int bits, unsigned int *value)
+{
+    int fd = fd_lookup(gpio);
+    char ch;
+    
+    if (!fd) {
+        if ((fd = open_value_file(gpio)) == -1) {
+            char err[256];
+            snprintf(err, sizeof(err), "gpio_get_more: could not open GPIO %d value file", gpio);
+            add_error_msg(err);
+            return -1;
+        }
+    }
+
+    // Loop for our number of bits
+    int i;
+    for (i = 0; i < bits; i++) {
+
+        if (lseek(fd, 0, SEEK_SET) < 0) {
+            char err[256];
+            snprintf(err, sizeof(err), "gpio_get_more: could not seek GPIO %d (%s)", gpio, strerror(errno));
+            add_error_msg(err);
+            return -1;
+        }
+        ssize_t s = read(fd, &ch, sizeof(ch));
+        if (s < 0) {
+            char err[256];
+            snprintf(err, sizeof(err), "gpio_get_more: could not read GPIO %d (%s)", gpio, strerror(errno));
+            add_error_msg(err);
+            return -1;
+        }
+    
+        if (ch == '1') {
+            *value |= (1 << i);
+        } else if (ch == '0') {
+            *value |= (0 << i);
+        } else {
+            char err[256];
+            snprintf(err, sizeof(err), "gpio_get_more: unrecognized read GPIO %d (%c)", gpio, ch);
+            add_error_msg(err);
+            return -1;
+        }
+        if (DEBUG) {
+            printf(" ** gpio_get_more: %c **\n", ch);
+            printf(" ** gpio_get_more: current value: %u **\n", *value);
+        }
+    }
+
+    return 0;
+    
+}
+
 int gpio_set_edge(int gpio, unsigned int edge)
 {
     int fd;
@@ -472,6 +612,9 @@ int gpio_set_edge(int gpio, unsigned int edge)
         return -1;
     }
 
+    if (DEBUG)
+        printf(" ** gpio_set_edge: %s **\n", stredge[edge]);
+
     ssize_t s = write(fd, stredge[edge], strlen(stredge[edge]) + 1);
     if (s < 0) {
         char err[256];
@@ -521,6 +664,9 @@ int gpio_get_edge(int gpio)
         return -1;
     }
 
+    if (DEBUG)
+        printf(" ** gpio_get_edge: %s **\n", edge);
+
     if (strcmp(edge, "rising") == 0)
     {
         rtnedge = 1;
@@ -553,6 +699,8 @@ int gpio_lookup(int fd)
 void exports_cleanup(void)
 {
     // unexport everything
+    if (DEBUG)
+        printf(" ** exports_cleanup **\n");
     while (exported_gpios != NULL)
         gpio_unexport(exported_gpios->gpio);
 }
@@ -562,6 +710,8 @@ int add_edge_callback(int gpio, int edge, void (*func)(int gpio, void* data), vo
     struct callback *cb = callbacks;
     struct callback *new_cb;
 
+    if (DEBUG)
+        printf(" ** add_edge_callback **\n");
     new_cb = malloc(sizeof(struct callback));  ASSRT(new_cb != NULL);
 
     new_cb->fde  = open_edge_file(gpio);
@@ -611,6 +761,8 @@ void run_callbacks(int gpio)
             // Only run if we are allowed
             if (canrun)
             {
+                if (DEBUG)
+                    printf(" ** run_callbacks: gpio triggered: %d **\n", gpio);
                 cb->func(cb->gpio, cb->data);
             }
 
@@ -629,6 +781,8 @@ void remove_callbacks(int gpio)
     {
         if (cb->gpio == gpio)
         {
+            if (DEBUG)
+                printf(" ** remove_callbacks: gpio: %d **\n", gpio);
             close(cb->fde);
             if (prev == NULL)
                 callbacks = cb->next;
@@ -762,6 +916,9 @@ int add_edge_detect(int gpio, unsigned int edge)
     struct epoll_event ev;
     long t = 0;
 
+    if (DEBUG)
+        printf(" ** add_edge_detect: gpio: %d **\n", gpio);
+
     // check to see if this gpio has been added already
     if (gpio_event_add(gpio) != 0)
         return 1;
@@ -828,6 +985,9 @@ void remove_edge_detect(int gpio)
     struct epoll_event ev;
     int fd = fd_lookup(gpio);
 
+    if (DEBUG)
+        printf(" ** remove_edge_detect: gpio : %d **\n", gpio);
+
     // delete callbacks for gpio
     remove_callbacks(gpio);
 
@@ -871,6 +1031,9 @@ int blocking_wait_for_edge(int gpio, unsigned int edge)
     struct epoll_event events, ev;
     char buf;
 
+    if (DEBUG)
+        printf(" ** blocking_wait_for_edge: gpio: %d **\n", gpio);
+
     if ((epfd = epoll_create(1)) == -1) {
         char err[256];
         snprintf(err, sizeof(err), "blocking_wait_for_edge: could not epoll_create GPIO %d (%s)", gpio, strerror(errno));
@@ -949,6 +1112,9 @@ int blocking_wait_for_edge(int gpio, unsigned int edge)
         }
     }
 
+    if (DEBUG)
+        printf(" ** blocking_wait_for_edge: gpio triggered: %d **\n", gpio);
+
     gpio_event_remove(gpio);
     close(epfd);
     return 0;

source/event_gpio.h

@@ -36,6 +36,8 @@ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
 SOFTWARE.
 */
 
+#include <stdint.h>
+
 #define NO_EDGE      0
 #define RISING_EDGE  1
 #define FALLING_EDGE 2
@@ -54,6 +56,12 @@ SOFTWARE.
 #define PUD_DOWN 1
 #define PUD_UP   2
 
+extern uint8_t *memmap;
+
+int map_pio_memory(void);
+int gpio_get_pud(int port, int pin);
+int gpio_set_pud(int port, int pin, uint8_t value);
+
 int gpio_export(int gpio);
 int gpio_unexport(int gpio);
 void exports_cleanup(void);
@@ -61,6 +69,7 @@ int gpio_set_direction(int gpio, unsigned int in_flag);
 int gpio_get_direction(int gpio, unsigned int *value);
 int gpio_set_value(int gpio, unsigned int value);
 int gpio_get_value(int gpio, unsigned int *value);
+int gpio_get_more(int gpio, int bits, unsigned int *value);
 int fd_lookup(int gpio);
 int open_value_file(int gpio);
 

source/py_gpio.c

@@ -43,6 +43,7 @@ SOFTWARE.
 #include "event_gpio.h"
 
 static int gpio_warnings = 1;
+static int r8_mem_setup = 0;
 
 int max_gpio = -1;
 dyn_int_array_t *gpio_direction = NULL;
@@ -58,26 +59,94 @@ struct py_callback
 };
 static struct py_callback *py_callbacks = NULL;
 
+// python function toggle_debug()
+static PyObject *py_toggle_debug(PyObject *self, PyObject *args)
+{
+    // toggle debug printing
+    toggle_debug();
+
+    Py_RETURN_NONE;
+}
+
 static int init_module(void)
 {
+    clear_error_msg();
+
+    // If we make it here, we're good to go
+    if (DEBUG)
+        printf(" ** init_module: setup complete **\n");
     module_setup = 1;
 
     return 0;
 }
 
+static int init_r8_gpio_mem(void)
+{
+    clear_error_msg();
+
+    if (DEBUG)
+        printf(" ** init_r8_gpio_mem: mapping memory **\n");
+    
+    if (map_pio_memory() < 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "init_r8_gpio_mem error (%s)", get_error_msg());
+        PyErr_SetString(PyExc_RuntimeError, err);
+        return 0;
+    }
+
+    // If we make it here, we're good to go
+    if (DEBUG)
+        printf(" ** init_r8_gpio_mem: setup complete **\n");
+    r8_mem_setup = 1;
+    
+    return 0;
+}
+
+// python function value = is_chip_pro
+static PyObject *py_is_chip_pro(PyObject *self, PyObject *args)
+{
+    PyObject *py_value;
+    
+    py_value = Py_BuildValue("i", is_this_chippro());
+
+    return py_value;
+}
 
 static void remember_gpio_direction(int gpio, int direction)
 {
     dyn_int_array_set(&gpio_direction, gpio, direction, -1);
 }
 
-// python function cleanup()
-static PyObject *py_cleanup(PyObject *self, PyObject *args)
+// Dummy function to mimic RPi.GPIO for easier porting.
+// python function setmode(mode)
+static PyObject *py_setmode(PyObject *self, PyObject *args)
 {
+    Py_RETURN_NONE;
+}
+
+// python function cleanup(channel=None)
+static PyObject *py_cleanup(PyObject *self, PyObject *args, PyObject *kwargs)
+{
+    int gpio;
+    char *channel;
+    static char *kwlist[] = {"channel", NULL};
+
     clear_error_msg();
 
-    // clean up any exports
+    // Channel is optional
+    if (!PyArg_ParseTupleAndKeywords(args, kwargs, "|s", kwlist, &channel)) {
+        return NULL;
+    }
+
+    // The !channel fixes issues #50
+    if (channel == NULL || strcmp(channel, "\0") == 0) {
         event_cleanup();
+    } else {
+        if (get_gpio_number(channel, &gpio) < 0) {
+            event_cleanup();
+        }
+        gpio_unexport(gpio);
+    }
 
     Py_RETURN_NONE;
 }
@@ -86,6 +155,7 @@ static PyObject *py_cleanup(PyObject *self, PyObject *args)
 static PyObject *py_setup_channel(PyObject *self, PyObject *args, PyObject *kwargs)
 {
     int gpio;
+    int allowed = -1;
     char *channel;
     int direction;
     int pud = PUD_OFF;
@@ -101,15 +171,16 @@ static PyObject *py_setup_channel(PyObject *self, PyObject *args, PyObject *kwar
         init_module();
     }
  
-
     if (direction != INPUT && direction != OUTPUT)
     {
         PyErr_SetString(PyExc_ValueError, "An invalid direction was passed to setup()");
         return NULL;
     }
     
-   if (direction == OUTPUT)
+    // Force pud to be off if we're configured for output
+    if (direction == OUTPUT) {
         pud = PUD_OFF;
+    }
  
     if (pud != PUD_OFF && pud != PUD_DOWN && pud != PUD_UP)
     {
@@ -124,6 +195,26 @@ static PyObject *py_setup_channel(PyObject *self, PyObject *args, PyObject *kwar
         return NULL;
     }
     
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    // Only map /dev/mem if we're not an XIO
+    if (!r8_mem_setup && !(gpio >= lookup_gpio_by_name("XIO-P0") && gpio <= lookup_gpio_by_name("XIO-P7"))) {
+        init_r8_gpio_mem();
+    }
+ 
     if (gpio_export(gpio) < 0) {
         char err[2000];
         snprintf(err, sizeof(err), "Error setting up channel %s, maybe already exported? (%s)", channel, get_error_msg());
@@ -136,6 +227,23 @@ static PyObject *py_setup_channel(PyObject *self, PyObject *args, PyObject *kwar
         PyErr_SetString(PyExc_RuntimeError, err);
         return NULL;
     }
+    
+    // Pull Up/Down
+    // Only if the pin we want is able to use it (R8 Owned, no XIO)
+    int port, pin;
+    if (compute_port_pin(channel, gpio, &port, &pin) == 0) {
+        // Set the PUD
+        gpio_set_pud(port, pin, pud);
+        // Check it was set properly
+        int pudr = gpio_get_pud(port, pin);
+        if (pudr != pud) {
+            char err[2000];
+            snprintf(err, sizeof(err), "Error setting pull up down %d on channel %s", pud, channel);
+            PyErr_SetString(PyExc_RuntimeError, err);
+            return NULL;
+        }
+    }
+    
     if (direction == OUTPUT) {
         if (gpio_set_value(gpio, initial) < 0) {
             char err[2000];
@@ -157,6 +265,7 @@ static PyObject *py_output_gpio(PyObject *self, PyObject *args)
     int gpio;
     int value;
     char *channel;
+    int allowed = -1;
 
     clear_error_msg();
 
@@ -168,6 +277,21 @@ static PyObject *py_output_gpio(PyObject *self, PyObject *args)
         return NULL;
     }
 
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
     if (!module_setup || dyn_int_array_get(&gpio_direction, gpio, -1) != OUTPUT)
     {
         char err[2000];
@@ -195,6 +319,7 @@ static PyObject *py_input_gpio(PyObject *self, PyObject *args)
     char *channel;
     unsigned int value;
     PyObject *py_value;
+    int allowed = -1;
 
     clear_error_msg();
 
@@ -206,6 +331,21 @@ static PyObject *py_input_gpio(PyObject *self, PyObject *args)
         return NULL;
     }
 
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
    // check channel is set up as an input or output
     if (!module_setup || (dyn_int_array_get(&gpio_direction, gpio, -1) == -1))
     {
@@ -225,6 +365,115 @@ static PyObject *py_input_gpio(PyObject *self, PyObject *args)
     return py_value;
 }
 
+//TODO: Come up with a way to merge py_read_byte_gpio and py_read_word_gpio
+// python function value = read_byte(channel)
+static PyObject *py_read_byte_gpio(PyObject *self, PyObject *args)
+{
+    int gpio;
+    char *channel;
+    unsigned int value = 0;
+    PyObject *py_value;
+    int allowed = -1;
+
+    clear_error_msg();
+
+    if (!PyArg_ParseTuple(args, "s", &channel))
+        return NULL;
+
+    if (get_gpio_number(channel, &gpio)) {
+        PyErr_SetString(PyExc_ValueError, "Invalid channel");
+        return NULL;
+    }
+
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+   // check channel is set up as an input or output
+    if (!module_setup || (dyn_int_array_get(&gpio_direction, gpio, -1) == -1))
+    {
+        PyErr_SetString(PyExc_RuntimeError, "You must setup() the GPIO channel first");
+        return NULL;
+    }
+
+    // We only want to get a 8 bits here
+    if (gpio_get_more(gpio, 8, &value) < 0) {
+      char err[1024];
+      snprintf(err, sizeof(err), "Could not get 8 bits of data ('%s')", get_error_msg());
+      PyErr_SetString(PyExc_RuntimeError, err);
+      return NULL;
+    }
+
+    py_value = Py_BuildValue("i", value);
+
+    return py_value;
+}
+
+// python function value = read_word(channel)
+static PyObject *py_read_word_gpio(PyObject *self, PyObject *args)
+{
+    int gpio;
+    char *channel;
+    unsigned int value = 0;
+    PyObject *py_value;
+    int allowed = -1;
+
+    clear_error_msg();
+
+    if (!PyArg_ParseTuple(args, "s", &channel))
+        return NULL;
+
+    if (get_gpio_number(channel, &gpio)) {
+        PyErr_SetString(PyExc_ValueError, "Invalid channel");
+        return NULL;
+    }
+    
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+    
+    // check channel is set up as an input or output
+    if (!module_setup || (dyn_int_array_get(&gpio_direction, gpio, -1) == -1))
+    {
+        PyErr_SetString(PyExc_RuntimeError, "You must setup() the GPIO channel first");
+        return NULL;
+    }
+
+    // We only want to get a 8 bits here
+    if (gpio_get_more(gpio, 16, &value) < 0) {
+      char err[1024];
+      snprintf(err, sizeof(err), "Could not get 16 bits of data ('%s')", get_error_msg());
+      PyErr_SetString(PyExc_RuntimeError, err);
+      return NULL;
+    }
+
+    py_value = Py_BuildValue("i", value);
+
+    return py_value;
+}
+
 static void run_py_callbacks(int gpio, void* data)
 {
    PyObject *result;
@@ -303,6 +552,7 @@ static PyObject *py_add_event_callback(PyObject *self, PyObject *args, PyObject
 {
    int gpio;
    char *channel;
+   int allowed = -1;
    unsigned int bouncetime = 0;
    PyObject *cb_func;
    char *kwlist[] = {"gpio", "callback", "bouncetime", NULL};
@@ -323,6 +573,21 @@ static PyObject *py_add_event_callback(PyObject *self, PyObject *args, PyObject
         return NULL;
     }
 
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
    // check to ensure gpio is one of the allowed pins
    if (gpio != lookup_gpio_by_name("AP-EINT3")
        && gpio != lookup_gpio_by_name("AP-EINT1")
@@ -357,6 +622,7 @@ static PyObject *py_add_event_detect(PyObject *self, PyObject *args, PyObject *k
    char *channel;
    int edge, result;
    unsigned int bouncetime = 0;
+   int allowed = -1;
    PyObject *cb_func = NULL;
    char *kwlist[] = {"gpio", "edge", "callback", "bouncetime", NULL};
 
@@ -376,6 +642,21 @@ static PyObject *py_add_event_detect(PyObject *self, PyObject *args, PyObject *k
        return NULL;
    }
 
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
    // check to ensure gpio is one of the allowed pins
    if (gpio != lookup_gpio_by_name("AP-EINT3")
        && gpio != lookup_gpio_by_name("AP-EINT1")
@@ -425,6 +706,7 @@ static PyObject *py_remove_event_detect(PyObject *self, PyObject *args)
    struct py_callback *cb = py_callbacks;
    struct py_callback *temp;
    struct py_callback *prev = NULL;
+   int allowed = -1;
 
    clear_error_msg();
 
@@ -436,6 +718,21 @@ static PyObject *py_remove_event_detect(PyObject *self, PyObject *args)
        return NULL;
    }
 
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
    // check to ensure gpio is one of the allowed pins
    if (gpio != lookup_gpio_by_name("AP-EINT3")
        && gpio != lookup_gpio_by_name("AP-EINT1")
@@ -473,6 +770,7 @@ static PyObject *py_event_detected(PyObject *self, PyObject *args)
 {
    int gpio;
    char *channel;
+   int allowed = -1;
 
    clear_error_msg();
 
@@ -484,6 +782,21 @@ static PyObject *py_event_detected(PyObject *self, PyObject *args)
        return NULL;
    }
 
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
    if (event_detected(gpio))
       Py_RETURN_TRUE;
    else
@@ -497,6 +810,7 @@ static PyObject *py_wait_for_edge(PyObject *self, PyObject *args)
    int edge, result;
    char *channel;
    char error[81];
+   int allowed = -1;
 
    clear_error_msg();
 
@@ -508,6 +822,21 @@ static PyObject *py_wait_for_edge(PyObject *self, PyObject *args)
        return NULL;
    }
 
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
    // check to ensure gpio is one of the allowed pins
    if (gpio != lookup_gpio_by_name("AP-EINT3")
        && gpio != lookup_gpio_by_name("AP-EINT1")
@@ -556,6 +885,7 @@ static PyObject *py_gpio_function(PyObject *self, PyObject *args)
     unsigned int value;
     PyObject *func;
     char *channel;
+    int allowed = -1;
 
     clear_error_msg();
 
@@ -567,6 +897,21 @@ static PyObject *py_gpio_function(PyObject *self, PyObject *args)
         return NULL;
     }
 
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
     if (setup_error)
     {
         PyErr_SetString(PyExc_RuntimeError, "Module not imported correctly!");
@@ -717,10 +1062,6 @@ static PyObject *py_selftest(PyObject *self, PyObject *args)
   ASSRT(0 == build_path("/home", "ip", fp, sizeof(fp)));
   ASSRT(0 == build_path("/NOTFOUND", "ch", fp, sizeof(fp)));
 
-  printf("Testing get_spi_bus_path_number\n");
-  ASSRT(2 == get_spi_bus_path_number(0));  /* doesn't really work on CHIP */
-  ASSRT(2 == get_spi_bus_path_number(1));  /* doesn't really work on CHIP */
-
   printf("Testing error message buffer\n");
   clear_error_msg();
   ASSRT(0 == strlen(get_error_msg()));
@@ -749,9 +1090,6 @@ static PyObject *py_selftest(PyObject *self, PyObject *args)
 
 static const char moduledocstring[] = "GPIO functionality of a CHIP using Python";
 
-
-
-
 /*
 mine for changing pin directipn
 */
@@ -761,6 +1099,7 @@ static PyObject *py_set_direction(PyObject *self, PyObject *args, PyObject *kwar
 	int gpio;
 	char *channel;
 	int direction;
+	int allowed = -1;
 	static char *kwlist[] = { "channel", "direction", NULL };
 
 	clear_error_msg();
@@ -785,6 +1124,21 @@ static PyObject *py_set_direction(PyObject *self, PyObject *args, PyObject *kwar
 		return NULL;
 	}
 
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
 	if (gpio_set_direction(gpio, direction) < 0) {
 		char err[2000];
 		snprintf(err, sizeof(err), "Error setting direction %d on channel %s. (%s)", direction, channel, get_error_msg());
@@ -799,9 +1153,11 @@ static PyObject *py_set_direction(PyObject *self, PyObject *args, PyObject *kwar
 
 PyMethodDef gpio_methods[] = {
    {"setup", (PyCFunction)py_setup_channel, METH_VARARGS | METH_KEYWORDS, "Set up the GPIO channel, direction and (optional) pull/up down control\nchannel        - Either: CHIP board pin number (not R8 GPIO 00..nn number).  Pins start from 1\n                 or    : CHIP GPIO name\ndirection      - INPUT or OUTPUT\n[pull_up_down] - PUD_OFF (default), PUD_UP or PUD_DOWN\n[initial]      - Initial value for an output channel"},
-   {"cleanup", py_cleanup, METH_VARARGS, "Clean up by resetting all GPIO channels that have been used by this program to INPUT with no pullup/pulldown and no event detection"},
+   {"cleanup", (PyCFunction)py_cleanup, METH_VARARGS | METH_KEYWORDS, "Clean up by resetting all GPIO channels that have been used by this program to INPUT with no pullup/pulldown and no event detection"},
    {"output", py_output_gpio, METH_VARARGS, "Output to a GPIO channel\ngpio  - gpio channel\nvalue - 0/1 or False/True or LOW/HIGH"},
    {"input", py_input_gpio, METH_VARARGS, "Input from a GPIO channel.  Returns HIGH=1=True or LOW=0=False\ngpio - gpio channel"},
+   {"read_byte", py_read_byte_gpio, METH_VARARGS, "Read a byte (8 bits) from a set of GPIO channels. Returns 8-bits of integer data\ngpio - gpio channel."},
+   {"read_word", py_read_word_gpio, METH_VARARGS, "Read a word (16 bits) from a set of GPIO channels. Returns 16-bits of integer data\ngpio - gpio channel."},
    {"add_event_detect", (PyCFunction)py_add_event_detect, METH_VARARGS | METH_KEYWORDS, "Enable edge detection events for a particular GPIO channel.\nchannel      - either board pin number or BCM number depending on which mode is set.\nedge         - RISING, FALLING or BOTH\n[callback]   - A callback function for the event (optional)\n[bouncetime] - Switch bounce timeout in ms for callback"},
    {"remove_event_detect", py_remove_event_detect, METH_VARARGS, "Remove edge detection for a particular GPIO channel\ngpio - gpio channel"},
    {"event_detected", py_event_detected, METH_VARARGS, "Returns True if an edge has occured on a given GPIO.  You need to enable edge detection using add_event_detect() first.\ngpio - gpio channel"},
@@ -811,13 +1167,16 @@ PyMethodDef gpio_methods[] = {
    {"setwarnings", py_setwarnings, METH_VARARGS, "Enable or disable warning messages"},
    {"get_gpio_base", py_gpio_base, METH_VARARGS, "Get the XIO base number for sysfs"},
    {"selftest", py_selftest, METH_VARARGS, "Internal unit tests"},
-   { "direction", (PyCFunction)py_set_direction, METH_VARARGS, "Change direction of gpio channel. Either INPUT or OUTPUT\n" },
+   {"direction", (PyCFunction)py_set_direction, METH_VARARGS | METH_KEYWORDS, "Change direction of gpio channel. Either INPUT or OUTPUT\n" },
+   {"setmode", (PyCFunction)py_setmode, METH_VARARGS, "Dummy function that does nothing but maintain compatibility with RPi.GPIO\n" },
+   {"toggle_debug", py_toggle_debug, METH_VARARGS, "Toggles the enabling/disabling of Debug print output"},
+   {"is_chip_pro", py_is_chip_pro, METH_VARARGS, "Is hardware a CHIP Pro? Boolean False for normal CHIP/PocketCHIP (R8 SOC)"},
    {NULL, NULL, 0, NULL}
 };
 
 
 #if PY_MAJOR_VERSION > 2
-static struct PyModuleDef rpigpiomodule = {
+static struct PyModuleDef chipgpiomodule = {
    PyModuleDef_HEAD_INIT,
    "GPIO",       // name of module
    moduledocstring,  // module documentation, may be NULL
@@ -837,7 +1196,7 @@ PyMODINIT_FUNC initGPIO(void)
    clear_error_msg();
 
 #if PY_MAJOR_VERSION > 2
-   if ((module = PyModule_Create(&rpigpiomodule)) == NULL)
+   if ((module = PyModule_Create(&chipgpiomodule)) == NULL)
       return NULL;
 #else
    if ((module = Py_InitModule3("GPIO", gpio_methods, moduledocstring)) == NULL)

source/py_pwm.c

@@ -47,11 +47,33 @@ static PyObject *py_cleanup(PyObject *self, PyObject *args)
 static PyObject *py_toggle_debug(PyObject *self, PyObject *args)
 {
     // toggle debug printing
-    pwm_toggle_debug();
+    toggle_debug();
 
     Py_RETURN_NONE;
 }
 
+static int init_module(void)
+{
+    clear_error_msg();
+
+    // If we make it here, we're good to go
+    if (DEBUG)
+        printf(" ** init_module: setup complete **\n");
+    module_setup = 1;
+
+    return 0;
+}
+
+// python function value = is_chip_pro
+static PyObject *py_is_chip_pro(PyObject *self, PyObject *args)
+{
+    PyObject *py_value;
+    
+    py_value = Py_BuildValue("i", is_this_chippro());
+
+    return py_value;
+}
+
 // python function start(channel, duty_cycle, freq)
 static PyObject *py_start_channel(PyObject *self, PyObject *args, PyObject *kwargs)
 {
@@ -60,25 +82,45 @@ static PyObject *py_start_channel(PyObject *self, PyObject *args, PyObject *kwar
     float frequency = 2000.0;
     float duty_cycle = 0.0;
     int polarity = 0;
+    int allowed = -1;
     static char *kwlist[] = {"channel", "duty_cycle", "frequency", "polarity", NULL};
 
+    clear_error_msg();
+
     if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|ffi", kwlist, &channel, &duty_cycle, &frequency, &polarity)) {
         return NULL;
     }
 
+    if (!module_setup) {
+        init_module();
+    }
+
     if (!get_pwm_key(channel, key)) {
         PyErr_SetString(PyExc_ValueError, "Invalid PWM key or name.");
         return NULL;
     }
 
-    if (duty_cycle < 0.0 || duty_cycle > 100.0)
-    {
+    // Check to see if PWM is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = pwm_allowed(key);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM %s not available on current Hardware", key);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    if (duty_cycle < 0.0 || duty_cycle > 100.0) {
         PyErr_SetString(PyExc_ValueError, "duty_cycle must have a value from 0.0 to 100.0");
         return NULL;
     }
 
-    if (frequency <= 0.0)
-    {
+    if (frequency <= 0.0) {
         PyErr_SetString(PyExc_ValueError, "frequency must be greater than 0.0");
         return NULL;
     }
@@ -88,8 +130,12 @@ static PyObject *py_start_channel(PyObject *self, PyObject *args, PyObject *kwar
         return NULL;
     }
 
-    if (!pwm_start(key, duty_cycle, frequency, polarity))
+    if (pwm_start(key, duty_cycle, frequency, polarity) < 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Unable to start PWM: %s (%s)", channel, get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
         return NULL;
+    }
 
     Py_RETURN_NONE;
 }
@@ -99,6 +145,9 @@ static PyObject *py_stop_channel(PyObject *self, PyObject *args, PyObject *kwarg
 {
     char key[8];
     char *channel;
+    int allowed = -1;
+
+    clear_error_msg();
 
     if (!PyArg_ParseTuple(args, "s", &channel))
         return NULL;
@@ -108,7 +157,27 @@ static PyObject *py_stop_channel(PyObject *self, PyObject *args, PyObject *kwarg
         return NULL;
     }
 
-    pwm_disable(key);
+    // Check to see if PWM is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = pwm_allowed(key);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM %s not available on current Hardware", key);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    if (pwm_disable(key) < 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM: %s issue: (%s)", channel, get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
 
     Py_RETURN_NONE;
 }
@@ -118,14 +187,16 @@ static PyObject *py_set_duty_cycle(PyObject *self, PyObject *args, PyObject *kwa
 {
     char key[8];
     char *channel;
+    int allowed = -1;
     float duty_cycle = 0.0;
     static char *kwlist[] = {"channel", "duty_cycle", NULL};
 
+    clear_error_msg();
+
     if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|f", kwlist, &channel, &duty_cycle))
         return NULL;
 
-    if (duty_cycle < 0.0 || duty_cycle > 100.0)
-    {
+    if (duty_cycle < 0.0 || duty_cycle > 100.0) {
         PyErr_SetString(PyExc_ValueError, "duty_cycle must have a value from 0.0 to 100.0");
         return NULL;
     }
@@ -135,8 +206,82 @@ static PyObject *py_set_duty_cycle(PyObject *self, PyObject *args, PyObject *kwa
         return NULL;
     }
 
+    // Check to see if PWM is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = pwm_allowed(key);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM %s not available on current Hardware", key);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
     if (pwm_set_duty_cycle(key, duty_cycle) == -1) {
-        PyErr_SetString(PyExc_RuntimeError, "You must start() the PWM channel first");
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM: %s issue: (%s)", channel, get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    Py_RETURN_NONE;
+}
+
+// python method PWM.set_pulse_width(channel, pulse_width_ns)
+static PyObject *py_set_pulse_width_ns(PyObject *self, PyObject *args, PyObject *kwargs)
+{
+    char key[8];
+    char *channel;
+    int allowed = -1;
+    unsigned long pulse_width_ns = 0.0;
+    unsigned long period_ns;
+    static char *kwlist[] = {"channel", "pulse_width_ns", NULL};
+
+    clear_error_msg();
+
+    if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|k", kwlist, &channel, &pulse_width_ns))
+        return NULL;
+
+    if (!get_pwm_key(channel, key)) {
+        PyErr_SetString(PyExc_ValueError, "Invalid PWM key or name.");
+        return NULL;
+    }
+
+    // Check to see if PWM is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = pwm_allowed(key);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM %s not available on current Hardware", key);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    // Get the period out of the data struct
+    int rtn = pwm_get_period_ns(key, &period_ns);
+    if (rtn == -1) {
+        PyErr_SetString(PyExc_ValueError, "period unable to be obtained");
+        return NULL;
+    }
+
+	if (pulse_width_ns < 0.0 || pulse_width_ns > period_ns) {
+        PyErr_SetString(PyExc_ValueError, "pulse width must have a value from 0 to period");
+        return NULL;
+    }
+
+    if (pwm_set_pulse_width_ns(key, pulse_width_ns) < 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM: %s issue: (%s)", channel, get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
         return NULL;
     }
 
@@ -148,14 +293,16 @@ static PyObject *py_set_frequency(PyObject *self, PyObject *args, PyObject *kwar
 {
     char key[8];
     char *channel;
+    int allowed = -1;
     float frequency = 1.0;
     static char *kwlist[] = {"channel", "frequency", NULL};
 
+    clear_error_msg();
+
     if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|f", kwlist, &channel, &frequency))
         return NULL;
 
-    if (frequency <= 0.0)
-    {
+    if (frequency <= 0.0) {
         PyErr_SetString(PyExc_ValueError, "frequency must be greater than 0.0");
         return NULL;
     }
@@ -165,14 +312,79 @@ static PyObject *py_set_frequency(PyObject *self, PyObject *args, PyObject *kwar
         return NULL;
     }
 
-    if (pwm_set_frequency(key, frequency) == -1) {
-        PyErr_SetString(PyExc_RuntimeError, "You must start() the PWM channel first");
+    // Check to see if PWM is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = pwm_allowed(key);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM %s not available on current Hardware", key);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    if (pwm_set_frequency(key, frequency) < 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM: %s issue: (%s)", channel, get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
         return NULL;
     }
 
     Py_RETURN_NONE;
 }
 
+// python method PWM.set_period_ns(channel, period_ns)
+static PyObject *py_set_period_ns(PyObject *self, PyObject *args, PyObject *kwargs)
+{
+    char key[8];
+    char *channel;
+    int allowed = -1;
+    unsigned long period_ns = 2e6;
+    static char *kwlist[] = {"channel", "period_ns", NULL};
+
+    clear_error_msg();
+
+    if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|k", kwlist, &channel, &period_ns))
+        return NULL;
+
+    if (period_ns <= 0) {
+        PyErr_SetString(PyExc_ValueError, "period must be greater than 0ns");
+        return NULL;
+    }
+
+    if (!get_pwm_key(channel, key)) {
+        PyErr_SetString(PyExc_ValueError, "Invalid PWM key or name.");
+        return NULL;
+    }
+
+    // Check to see if PWM is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = pwm_allowed(key);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM %s not available on current Hardware", key);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    if (pwm_set_period_ns(key, period_ns) < 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "PWM: %s issue: (%s)", channel, get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    Py_RETURN_NONE;
+}
 
 static const char moduledocstring[] = "Hardware PWM functionality of a CHIP using Python";
 
@@ -181,9 +393,11 @@ PyMethodDef pwm_methods[] = {
     {"stop", (PyCFunction)py_stop_channel, METH_VARARGS | METH_KEYWORDS, "Stop the PWM channel.  channel can be in the form of 'PWM0', or 'U13_18'"},
     {"set_duty_cycle", (PyCFunction)py_set_duty_cycle, METH_VARARGS, "Change the duty cycle\ndutycycle - between 0.0 and 100.0" },
     {"set_frequency", (PyCFunction)py_set_frequency, METH_VARARGS, "Change the frequency\nfrequency - frequency in Hz (freq > 0.0)" },
+    {"set_period_ns", (PyCFunction)py_set_period_ns, METH_VARARGS, "Change the period\nperiod_ns - period in nanoseconds" },
+    {"set_pulse_width_ns", (PyCFunction)py_set_pulse_width_ns, METH_VARARGS, "Change the period\npulse_width_ns - pulse width in nanoseconds" },
     {"cleanup", py_cleanup, METH_VARARGS, "Clean up by resetting all GPIO channels that have been used by this program to INPUT with no pullup/pulldown and no event detection"},
     {"toggle_debug", py_toggle_debug, METH_VARARGS, "Toggles the enabling/disabling of Debug print output"},
-    //{"setwarnings", py_setwarnings, METH_VARARGS, "Enable or disable warning messages"},
+    {"is_chip_pro", py_is_chip_pro, METH_VARARGS, "Is hardware a CHIP Pro? Boolean False for normal CHIP/PocketCHIP (R8 SOC)"},
     {NULL, NULL, 0, NULL}
 };
 

source/py_servo.c

@@ -0,0 +1,349 @@
+/*
+Copyright (c) 2017 Robert Wolterman
+
+Using CHIP_IO servo code from Brady Hurlburt as a basis for the servo code
+
+Copyright (c) 2016 Brady Hurlburt
+
+Original BBIO Author Justin Cooper
+Modified for CHIP_IO Author Brady Hurlburt
+
+This file incorporates work covered by the following copyright and
+permission notice, all modified code adopts the original license:
+
+Copyright (c) 2013 Adafruit
+Author: Justin Cooper
+
+Permission is hereby granted, free of charge, to any person obtaining a copy of
+this software and associated documentation files (the "Software"), to deal in
+the Software without restriction, including without limitation the rights to
+use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies
+of the Software, and to permit persons to whom the Software is furnished to do
+so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all
+copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+SOFTWARE.
+*/
+
+#include "Python.h"
+#include "constants.h"
+#include "common.h"
+#include "c_softservo.h"
+
+// python function toggle_debug()
+static PyObject *py_toggle_debug(PyObject *self, PyObject *args)
+{
+    // toggle debug printing
+    toggle_debug();
+
+    Py_RETURN_NONE;
+}
+
+// python function cleanup()
+static PyObject *py_cleanup(PyObject *self, PyObject *args)
+{
+    // unexport the Servo
+    servo_cleanup();
+
+    Py_RETURN_NONE;
+}
+
+static int init_module(void)
+{
+    clear_error_msg();
+    
+    // If we make it here, we're good to go
+    if (DEBUG)
+        printf(" ** init_module: setup complete **\n");
+    module_setup = 1;
+
+    return 0;
+}
+
+// python function value = is_chip_pro
+static PyObject *py_is_chip_pro(PyObject *self, PyObject *args)
+{
+    PyObject *py_value;
+    
+    py_value = Py_BuildValue("i", is_this_chippro());
+
+    return py_value;
+}
+
+// python function start(channel, angle, range)
+static PyObject *py_start_channel(PyObject *self, PyObject *args, PyObject *kwargs)
+{
+    int gpio;
+    char key[8];
+    char *channel = NULL;
+    float angle = 0.0;
+    float range = 180.0;
+    int allowed = -1;
+    static char *kwlist[] = {"channel", "angle", "range", NULL};
+
+    clear_error_msg();
+
+    if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|ff", kwlist, &channel, &angle, &range)) {
+        return NULL;
+    }
+    ASSRT(channel != NULL);
+
+    if (!module_setup) {
+        init_module();
+    }
+
+    if (!get_key(channel, key)) {
+        PyErr_SetString(PyExc_ValueError, "Invalid Servo key or name.");
+        return NULL;
+    }
+
+    // check to ensure gpio is one of the allowed pins
+    // Not protecting the call as if the get_key() fails, we won't make it here
+    get_gpio_number(channel, &gpio);
+    if ((gpio >= lookup_gpio_by_name("XIO-P0") && gpio <= lookup_gpio_by_name("XIO-P7"))) {
+        PyErr_SetString(PyExc_ValueError, "Servo currently not available on XIO-P0 to XIO-P7");
+        return NULL;
+    }
+
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    if (servo_start(key, angle, range) < 0) {
+       printf("servo_start failed");
+       char err[2000];
+       snprintf(err, sizeof(err), "Error starting servo on pin %s (%s)", key, get_error_msg());
+       PyErr_SetString(PyExc_RuntimeError, err);
+       return NULL;
+    }
+
+    Py_RETURN_NONE;
+}
+
+// python function stop(channel)
+static PyObject *py_stop_channel(PyObject *self, PyObject *args, PyObject *kwargs)
+{
+    int gpio;
+    char key[8];
+    int allowed = -1;
+    char *channel;
+
+    clear_error_msg();
+
+    if (!PyArg_ParseTuple(args, "s", &channel))
+        return NULL;
+
+    if (!get_key(channel, key)) {
+        PyErr_SetString(PyExc_ValueError, "Invalid key or name");
+        return NULL;
+    }
+
+    // check to ensure gpio is one of the allowed pins
+    // Not protecting the call as if the get_key() fails, we won't make it here
+    get_gpio_number(channel, &gpio);
+    if ((gpio >= lookup_gpio_by_name("XIO-P0") && gpio <= lookup_gpio_by_name("XIO-P7"))) {
+        PyErr_SetString(PyExc_ValueError, "Servo currently not available on XIO-P0 to XIO-P7");
+        return NULL;
+    }
+
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    servo_disable(key);
+
+    Py_RETURN_NONE;
+}
+
+// python method SERVO.set_range(channel, duty_cycle)
+static PyObject *py_set_range(PyObject *self, PyObject *args, PyObject *kwargs)
+{
+    int gpio;
+    char key[8];
+    char *channel;
+    float range = 180.0;
+    int allowed = -1;
+    static char *kwlist[] = {"channel", "range", NULL};
+
+    clear_error_msg();
+
+    if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|f", kwlist, &channel, &range))
+        return NULL;
+
+    if (range > 360.0) {
+        PyErr_SetString(PyExc_ValueError, "range can not be greater than 360.0");
+        return NULL;
+    }
+
+    if (!get_key(channel, key)) {
+        PyErr_SetString(PyExc_ValueError, "Invalid key or name.");
+        return NULL;
+    }
+
+    // check to ensure gpio is one of the allowed pins
+    // Not protecting the call as if the get_key() fails, we won't make it here
+    get_gpio_number(channel, &gpio);
+    if ((gpio >= lookup_gpio_by_name("XIO-P0") && gpio <= lookup_gpio_by_name("XIO-P7"))) {
+        PyErr_SetString(PyExc_ValueError, "Servo currently not available on XIO-P0 to XIO-P7");
+        return NULL;
+    }
+
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    if (servo_set_range(key, range) == -1) {
+        PyErr_SetString(PyExc_RuntimeError, "You must start() the Servo channel first");
+        return NULL;
+    }
+
+    Py_RETURN_NONE;
+}
+
+// python method SERVO.set_angle(channel, duty_cycle)
+static PyObject *py_set_angle(PyObject *self, PyObject *args, PyObject *kwargs)
+{
+    int gpio;
+    char key[8];
+    char *channel;
+    float angle = 0.0;
+    int allowed = -1;
+    static char *kwlist[] = {"channel", "angle", NULL};
+
+    clear_error_msg();
+
+    if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|f", kwlist, &channel, &angle))
+        return NULL;
+
+    //if (range > 360.0) {
+    //    PyErr_SetString(PyExc_ValueError, "range can not be greater than 360.0");
+    //    return NULL;
+    //}
+
+    if (!get_key(channel, key)) {
+        PyErr_SetString(PyExc_ValueError, "Invalid key or name.");
+        return NULL;
+    }
+
+    // check to ensure gpio is one of the allowed pins
+    // Not protecting the call as if the get_key() fails, we won't make it here
+    get_gpio_number(channel, &gpio);
+    if ((gpio >= lookup_gpio_by_name("XIO-P0") && gpio <= lookup_gpio_by_name("XIO-P7"))) {
+        PyErr_SetString(PyExc_ValueError, "Servo currently not available on XIO-P0 to XIO-P7");
+        return NULL;
+    }
+
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    if (servo_set_angle(key, angle) == -1) {
+       char err[2000];
+       snprintf(err, sizeof(err), "Error setting servo angle on pin %s (%s)", key, get_error_msg());
+       PyErr_SetString(PyExc_RuntimeError, err);
+       return NULL;
+    }
+
+    Py_RETURN_NONE;
+}
+
+static const char moduledocstring[] = "Software Servo functionality of a CHIP using Python";
+
+PyMethodDef servo_methods[] = {
+    {"start", (PyCFunction)py_start_channel, METH_VARARGS | METH_KEYWORDS, "Set up and start the Servo.  channel can be in the form of 'XIO-P0', or 'U14_13'"},
+    {"stop", (PyCFunction)py_stop_channel, METH_VARARGS | METH_KEYWORDS, "Stop the Servo.  channel can be in the form of 'XIO-P0', or 'U14_13'"},
+    {"set_range", (PyCFunction)py_set_range, METH_VARARGS, "Change the servo range\nrange - max angular range of the servo" },
+    {"set_angle", (PyCFunction)py_set_angle, METH_VARARGS, "Change the servo angle\nangle - angle of the servo between +/-(range/2)" },
+    {"cleanup", (PyCFunction)py_cleanup, METH_VARARGS, "Clean up by resetting All or one Servo that have been used by this program."},
+    {"toggle_debug", py_toggle_debug, METH_VARARGS, "Toggles the enabling/disabling of Debug print output"},
+    {"is_chip_pro", py_is_chip_pro, METH_VARARGS, "Is hardware a CHIP Pro? Boolean False for normal CHIP/PocketCHIP (R8 SOC)"},
+    {NULL, NULL, 0, NULL}
+};
+
+#if PY_MAJOR_VERSION > 2
+static struct PyModuleDef chipservomodule = {
+    PyModuleDef_HEAD_INIT,
+    "SERVO",       // name of module
+    moduledocstring,  // module documentation, may be NULL
+    -1,               // size of per-interpreter state of the module, or -1 if the module keeps state in global variables.
+    servo_methods
+};
+#endif
+
+#if PY_MAJOR_VERSION > 2
+PyMODINIT_FUNC PyInit_SERVO(void)
+#else
+PyMODINIT_FUNC initSERVO(void)
+#endif
+{
+    PyObject *module = NULL;
+
+#if PY_MAJOR_VERSION > 2
+    if ((module = PyModule_Create(&chipservomodule)) == NULL)
+       return NULL;
+#else
+    if ((module = Py_InitModule3("SERVO", servo_methods, moduledocstring)) == NULL)
+       return;
+#endif
+
+   define_constants(module);
+
+
+#if PY_MAJOR_VERSION > 2
+    return module;
+#else
+    return;
+#endif
+}

source/py_softpwm.c

@@ -34,6 +34,15 @@ SOFTWARE.
 #include "common.h"
 #include "c_softpwm.h"
 
+// python function toggle_debug()
+static PyObject *py_toggle_debug(PyObject *self, PyObject *args)
+{
+    // toggle debug printing
+    toggle_debug();
+
+    Py_RETURN_NONE;
+}
+
 // python function cleanup()
 static PyObject *py_cleanup(PyObject *self, PyObject *args)
 {
@@ -43,6 +52,28 @@ static PyObject *py_cleanup(PyObject *self, PyObject *args)
     Py_RETURN_NONE;
 }
 
+static int init_module(void)
+{
+    clear_error_msg();
+
+    // If we make it here, we're good to go
+    if (DEBUG)
+        printf(" ** init_module: setup complete **\n");
+    module_setup = 1;
+
+    return 0;
+}
+
+// python function value = is_chip_pro
+static PyObject *py_is_chip_pro(PyObject *self, PyObject *args)
+{
+    PyObject *py_value;
+    
+    py_value = Py_BuildValue("i", is_this_chippro());
+
+    return py_value;
+}
+
 // python function start(channel, duty_cycle, freq)
 static PyObject *py_start_channel(PyObject *self, PyObject *args, PyObject *kwargs)
 {
@@ -51,26 +82,51 @@ static PyObject *py_start_channel(PyObject *self, PyObject *args, PyObject *kwar
     float frequency = 2000.0;
     float duty_cycle = 0.0;
     int polarity = 0;
+    int gpio;
+    int allowed = -1;
     static char *kwlist[] = {"channel", "duty_cycle", "frequency", "polarity", NULL};
 
+    clear_error_msg();
+
     if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|ffi", kwlist, &channel, &duty_cycle, &frequency, &polarity)) {
         return NULL;
     }
     ASSRT(channel != NULL);
 
+    if (!module_setup) {
+        init_module();
+    }
+
     if (!get_key(channel, key)) {
         PyErr_SetString(PyExc_ValueError, "Invalid SOFTPWM key or name.");
         return NULL;
     }
 
-    if (duty_cycle < 0.0 || duty_cycle > 100.0)
-    {
+    // check to ensure gpio is one of the allowed pins
+    // Not protecting the call as if the get_key() fails, we won't make it here
+    get_gpio_number(channel, &gpio);
+
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
+    if (duty_cycle < 0.0 || duty_cycle > 100.0) {
         PyErr_SetString(PyExc_ValueError, "duty_cycle must have a value from 0.0 to 100.0");
         return NULL;
     }
 
-    if (frequency <= 0.0)
-    {
+    if (frequency <= 0.0) {
         PyErr_SetString(PyExc_ValueError, "frequency must be greater than 0.0");
         return NULL;
     }
@@ -80,8 +136,7 @@ static PyObject *py_start_channel(PyObject *self, PyObject *args, PyObject *kwar
         return NULL;
     }
 
-    if (softpwm_start(key, duty_cycle, frequency, polarity) < 0)
-    {
+    if (softpwm_start(key, duty_cycle, frequency, polarity) < 0) {
        printf("softpwm_start failed");
        char err[2000];
        snprintf(err, sizeof(err), "Error starting softpwm on pin %s (%s)", key, get_error_msg());
@@ -97,6 +152,10 @@ static PyObject *py_stop_channel(PyObject *self, PyObject *args, PyObject *kwarg
 {
     char key[8];
     char *channel;
+    int gpio;
+    int allowed = -1;
+
+    clear_error_msg();
 
     if (!PyArg_ParseTuple(args, "s", &channel))
         return NULL;
@@ -106,6 +165,25 @@ static PyObject *py_stop_channel(PyObject *self, PyObject *args, PyObject *kwarg
         return NULL;
     }
 
+    // check to ensure gpio is one of the allowed pins
+    // Not protecting the call as if the get_key() fails, we won't make it here
+    get_gpio_number(channel, &gpio);
+
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
     softpwm_disable(key);
 
     Py_RETURN_NONE;
@@ -116,14 +194,17 @@ static PyObject *py_set_duty_cycle(PyObject *self, PyObject *args, PyObject *kwa
 {
     char key[8];
     char *channel;
+    int gpio;
+    int allowed = -1;
     float duty_cycle = 0.0;
     static char *kwlist[] = {"channel", "duty_cycle", NULL};
 
+    clear_error_msg();
+
     if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|f", kwlist, &channel, &duty_cycle))
         return NULL;
 
-    if (duty_cycle < 0.0 || duty_cycle > 100.0)
-    {
+    if (duty_cycle < 0.0 || duty_cycle > 100.0) {
         PyErr_SetString(PyExc_ValueError, "duty_cycle must have a value from 0.0 to 100.0");
         return NULL;
     }
@@ -133,6 +214,25 @@ static PyObject *py_set_duty_cycle(PyObject *self, PyObject *args, PyObject *kwa
         return NULL;
     }
 
+    // check to ensure gpio is one of the allowed pins
+    // Not protecting the call as if the get_key() fails, we won't make it here
+    get_gpio_number(channel, &gpio);
+
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
     if (softpwm_set_duty_cycle(key, duty_cycle) == -1) {
         PyErr_SetString(PyExc_RuntimeError, "You must start() the PWM channel first");
         return NULL;
@@ -146,14 +246,17 @@ static PyObject *py_set_frequency(PyObject *self, PyObject *args, PyObject *kwar
 {
     char key[8];
     char *channel;
+    int gpio;
+    int allowed = -1;
     float frequency = 1.0;
     static char *kwlist[] = {"channel", "frequency", NULL};
 
+    clear_error_msg();
+
     if (!PyArg_ParseTupleAndKeywords(args, kwargs, "s|f", kwlist, &channel, &frequency))
         return NULL;
 
-    if ((frequency <= 0.0) || (frequency > 10000.0))
-    {
+    if ((frequency <= 0.0) || (frequency > 10000.0)) {
         PyErr_SetString(PyExc_ValueError, "frequency must be greater than 0.0 and less than 10000.0");
         return NULL;
     }
@@ -163,6 +266,25 @@ static PyObject *py_set_frequency(PyObject *self, PyObject *args, PyObject *kwar
         return NULL;
     }
 
+    // check to ensure gpio is one of the allowed pins
+    // Not protecting the call as if the get_key() fails, we won't make it here
+    get_gpio_number(channel, &gpio);
+
+    // Check to see if GPIO is allowed on the hardware
+    // A 1 means we're good to go
+    allowed = gpio_allowed(gpio);
+    if (allowed == -1) {
+        char err[2000];
+        snprintf(err, sizeof(err), "Error determining hardware. (%s)", get_error_msg());
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    } else if (allowed == 0) {
+        char err[2000];
+        snprintf(err, sizeof(err), "GPIO %d not available on current Hardware", gpio);
+        PyErr_SetString(PyExc_ValueError, err);
+        return NULL;
+    }
+
     if (softpwm_set_frequency(key, frequency) == -1) {
         PyErr_SetString(PyExc_RuntimeError, "You must start() the PWM channel first");
         return NULL;
@@ -171,21 +293,21 @@ static PyObject *py_set_frequency(PyObject *self, PyObject *args, PyObject *kwar
     Py_RETURN_NONE;
 }
 
-
 static const char moduledocstring[] = "Software PWM functionality of a CHIP using Python";
 
 PyMethodDef pwm_methods[] = {
     {"start", (PyCFunction)py_start_channel, METH_VARARGS | METH_KEYWORDS, "Set up and start the PWM channel.  channel can be in the form of 'XIO-P0', or 'U14_13'"},
     {"stop", (PyCFunction)py_stop_channel, METH_VARARGS | METH_KEYWORDS, "Stop the PWM channel.  channel can be in the form of 'XIO-P0', or 'U14_13'"},
-    { "set_duty_cycle", (PyCFunction)py_set_duty_cycle, METH_VARARGS, "Change the duty cycle\ndutycycle - between 0.0 and 100.0" },
-    { "set_frequency", (PyCFunction)py_set_frequency, METH_VARARGS, "Change the frequency\nfrequency - frequency in Hz (freq > 0.0)" },
-    {"cleanup", py_cleanup, METH_VARARGS, "Clean up by resetting all GPIO channels that have been used by this program to INPUT with no pullup/pulldown and no event detection"},
-    //{"setwarnings", py_setwarnings, METH_VARARGS, "Enable or disable warning messages"},
+    {"set_duty_cycle", (PyCFunction)py_set_duty_cycle, METH_VARARGS, "Change the duty cycle\ndutycycle - between 0.0 and 100.0" },
+    {"set_frequency", (PyCFunction)py_set_frequency, METH_VARARGS, "Change the frequency\nfrequency - frequency in Hz (freq > 0.0)" },
+    {"cleanup", (PyCFunction)py_cleanup, METH_VARARGS, "Clean up by resetting all GPIO channels that have been used by this program to INPUT with no pullup/pulldown and no event detection"},
+    {"toggle_debug", py_toggle_debug, METH_VARARGS, "Toggles the enabling/disabling of Debug print output"},
+    {"is_chip_pro", py_is_chip_pro, METH_VARARGS, "Is hardware a CHIP Pro? Boolean False for normal CHIP/PocketCHIP (R8 SOC)"},
     {NULL, NULL, 0, NULL}
 };
 
 #if PY_MAJOR_VERSION > 2
-static struct PyModuleDef chippwmmodule = {
+static struct PyModuleDef chipspwmmodule = {
     PyModuleDef_HEAD_INIT,
     "SOFTPWM",       // name of module
     moduledocstring,  // module documentation, may be NULL
@@ -203,7 +325,7 @@ PyMODINIT_FUNC initSOFTPWM(void)
     PyObject *module = NULL;
 
 #if PY_MAJOR_VERSION > 2
-    if ((module = PyModule_Create(&chippwmmodule)) == NULL)
+    if ((module = PyModule_Create(&chipspwmmodule)) == NULL)
        return NULL;
 #else
     if ((module = Py_InitModule3("SOFTPWM", pwm_methods, moduledocstring)) == NULL)

test/integrations/lradctest.py

@@ -1,10 +1,8 @@
-#!/usr/bin/python
-
 import CHIP_IO.LRADC as ADC
 
 # == ENABLE DEBUG ==
 print("ENABLING LRADC DEBUG OUTPUT")
-ADC.enable_debug()
+ADC.toggle_debug()
 
 # == SETUP ==
 print("LRADC SETUP WITH SAMPLE RATE OF 125")

test/integrations/omtest.py

@@ -5,7 +5,7 @@ import os
 
 # ENABLE DEBUG
 print("ENABLING OVERLAY MANAGER DEBUG")
-OM.enable_debug()
+OM.toggle_debug()
 
 # **************** PWM *******************
 print("\nIS PWM ENABLED: {0}".format(OM.get_pwm_loaded()))
@@ -20,19 +20,6 @@ print("UNLOADING PWM0")
 OM.unload("PWM0")
 print("IS PWM ENABLED: {0}".format(OM.get_pwm_loaded()))
 
-# **************** I2C-1 *******************
-print("\nIS I2C ENABLED: {0}".format(OM.get_i2c_loaded()))
-OM.load("I2C1")
-print("IS I2C ENABLED: {0}".format(OM.get_i2c_loaded()))
-# VERIFY I2C-1 EXISTS
-if os.path.exists('/sys/class/i2c-dev/i2c-1'):
-    print("I2C1 DEVICE EXISTS")
-else:
-    print("I2C1 DEVICE DID NOT LOAD PROPERLY")
-print("UNLOADING I2C1")
-OM.unload("I2C1")
-print("IS I2C ENABLED: {0}".format(OM.get_i2c_loaded()))
-
 # **************** SPI2 *******************
 print("\nIS SPI ENABLED: {0}".format(OM.get_spi_loaded()))
 OM.load("SPI2")

test/integrations/servotest.py

@@ -0,0 +1,71 @@
+import CHIP_IO.SERVO as SERVO
+import CHIP_IO.GPIO as GPIO
+import time
+import datetime
+import threading
+
+class ServoTestReceiver(threading.Thread):
+    def __init__(self,gpio,key,maxcount=20,sleeptime=0.005):
+        self.gpio = gpio
+        self.key = key
+        self.counter = 0
+        self.maxcount = maxcount
+        self.sleeptime = sleeptime
+        self.dead = False
+        threading.Thread.__init__(self)
+
+    def kill(self):
+        self.dead = True
+
+    def run(self):
+        print("SETTING UP RECEIVER GPIO")
+        self.gpio.cleanup()
+        self.gpio.setup(self.key, self.gpio.IN)
+        print("STARTING RECEIVE LOOP")
+        try:
+            #while self.counter < self.maxcount:
+            while not self.dead:
+                pwmval = self.gpio.input(self.key)
+                print("SERVO VALUE: {0} @ {1}".format(pwmval, datetime.datetime.now()))
+                time.sleep(self.sleeptime)
+                self.counter += 1
+        except KeyboardInterrupt:
+            self.gpio.cleanup(self.key)
+
+
+if __name__ == "__main__":
+    # SETUP VARIABLES
+    SERVOGPIO = "CSID1" #"XIO-P7"
+    RECEIVERGPIO = "CSID7"
+    COUNT = 120
+    SLEEPTIME = 0.0001
+    RANGE = 180
+
+    # SETUP PWM
+    try:
+        print("SERVO START")
+        SERVO.toggle_debug()
+        SERVO.start(SERVOGPIO, 0, RANGE)
+
+        # SETUP SERVO RECEIVER
+        #rcvr = ServoTestReceiver(GPIO, RECEIVERGPIO, COUNT, SLEEPTIME)
+        #rcvr.start()
+
+        # LOOP THROUGH RANGE
+        for i in range(-(RANGE/2),(RANGE/2),5):
+            print("SETTING ANGLE: {0}".format(i))
+            SERVO.set_angle(SERVOGPIO, i)
+            time.sleep(1)
+        
+        #rcvr.kill()
+        raw_input("PRESS ENTER WHEN DONE")
+
+    except:
+        raise
+    finally:
+        # CLEANUP
+        print("CLEANUP")
+        SERVO.stop(SERVOGPIO)
+        SERVO.cleanup(SERVOGPIO)
+
+

test/integrations/spwmtest2.py

@@ -0,0 +1,45 @@
+#!/usr/bin/python
+
+import CHIP_IO.SOFTPWM as PWM
+import CHIP_IO.GPIO as GPIO
+import CHIP_IO.OverlayManager as OM
+import time
+import datetime
+
+if __name__ == "__main__":
+    # SETUP VARIABLES
+    PWMGPIO = "XIO-P7"
+    #PWMGPIO = "LCD-D4"
+    COUNT = 150
+    SLEEPTIME = 0.01
+
+    time.sleep(1)
+
+    # SETUP PWM
+    try:
+        print("PWM START")
+        #PWM.toggle_debug()
+        PWM.start(PWMGPIO, 50, 45, 1)
+
+        # UNCOMMENT FOR CRASH
+        print("PWM SET FREQUENCY")
+        PWM.set_frequency(PWMGPIO, 10)
+
+        # UNCOMMENT FOR CRASH
+        print("PWM SET DUTY CYCLE")
+        PWM.set_duty_cycle(PWMGPIO, 25)
+
+        #time.sleep(COUNT*SLEEPTIME + 1)
+        raw_input("PRESS ENTER WHEN DONE")
+
+    except:
+        raise
+    finally:
+        # CLEANUP
+        print("CLEANUP")
+        PWM.stop(PWMGPIO)
+        PWM.cleanup()
+        #OM.unload("PWM0")
+        #GPIO.cleanup()
+
+

test/test_lradc.py

@@ -0,0 +1,14 @@
+import pytest
+
+import CHIP_IO.LRADC as LRADC
+
+class TestLRADC:
+    def test_scale_factor(self):
+        assert LRADC.get_scale_factor() == 31.25
+        
+    def test_sample_rate_values(self):
+        assert LRADC.get_allowable_sample_rates() == (32.25, 62.5, 125, 250)
+
+    def test_set_sample_rate(self):
+        LRADC.set_sample_rate(32.25)
+        assert LRADC.get_sample_rate() == 32.25

test/test_pwm_setup.py

@@ -4,12 +4,15 @@ import time
 
 import CHIP_IO.PWM as PWM
 import CHIP_IO.OverlayManager as OM
+import CHIP_IO.Utilities as UT
 
 def setup_module(module):
+    if not UT.is_chip_pro():
         OM.load("PWM0")
 
 def teardown_module(module):
     PWM.cleanup()
+    if not UT.is_chip_pro():
         OM.unload("PWM0")
 
 class TestPwmSetup:
@@ -17,16 +20,6 @@ class TestPwmSetup:
     def setup_method(self, test_method):
         time.sleep(0.5)
 
-    #def teardown_method(self, test_method):
-    #    PWM.cleanup()
-        #OM.unload("PWM0")
-
-    #def setup_module(self, module):
-    #    OM.load("PWM0")
-
-    #def teardown_module(self, module):
-    #    OM.unload("PWM0")
-
     def test_start_pwm(self):
         PWM.start("PWM0", 0)
 
@@ -38,27 +31,25 @@ class TestPwmSetup:
         assert int(duty) == 0
         assert int(period) == 500000
 
-    @pytest.mark.xfail(reason="pwm cleanup is doing weirdness for this test")
     def test_start_pwm_with_polarity_one(self):
+        PWM.cleanup()
         PWM.start("PWM0", 0, 2000, 1)
 
         pwm_test = '/sys/class/pwm/pwmchip0/pwm0/'
 
-        #assert os.path.exists(pwm_test) == True
         duty = open(pwm_test + 'duty_cycle').readline().strip()
         period = open(pwm_test + 'period').readline().strip()
         polarity = open(pwm_test + 'polarity').readline().strip()
         assert int(duty) == 0
         assert int(period) == 500000
-        assert str(polarity) == "inverted"
+        assert str(polarity) == "inversed"
 
-    @pytest.mark.xfail(reason="pwm cleanup is doing weirdness for this test")
     def test_start_pwm_with_polarity_default(self):
+        PWM.cleanup()
         PWM.start("PWM0", 0, 2000, 0)
 
         pwm_test = '/sys/class/pwm/pwmchip0/pwm0/'
 
-        #assert os.path.exists(pwm_test) == True
         duty = open(pwm_test + 'duty_cycle').readline().strip()
         period = open(pwm_test + 'period').readline().strip()
         polarity = open(pwm_test + 'polarity').readline().strip()
@@ -66,13 +57,12 @@ class TestPwmSetup:
         assert int(period) == 500000
         assert str(polarity) == "normal"
 
-    @pytest.mark.xfail(reason="pwm cleanup is doing weirdness for this test")
     def test_start_pwm_with_polarity_zero(self):
+        PWM.cleanup()
         PWM.start("PWM0", 0, 2000, 0)
 
         pwm_test = '/sys/class/pwm/pwmchip0/pwm0/'
 
-        #assert os.path.exists(pwm_test) == True
         duty = open(pwm_test + 'duty_cycle').readline().strip()
         period = open(pwm_test + 'period').readline().strip()
         polarity = open(pwm_test + 'polarity').readline().strip()
@@ -90,11 +80,14 @@ class TestPwmSetup:
 
     def test_pwm_start_valid_duty_cycle_min(self):
         #testing an exception isn't thrown
+        PWM.cleanup()
         PWM.start("PWM0", 0)
+        PWM.cleanup()
 
     def test_pwm_start_valid_duty_cycle_max(self):
         #testing an exception isn't thrown
         PWM.start("PWM0", 100)
+        PWM.cleanup()
 
     def test_pwm_start_invalid_duty_cycle_high(self):
         with pytest.raises(ValueError):
@@ -143,7 +136,8 @@ class TestPwmSetup:
         assert int(period) == 500000
 
     def test_pwm_duty_cycle_non_setup_key(self):
-        with pytest.raises(RuntimeError):
+        with pytest.raises(ValueError):
+            PWM.cleanup()
             PWM.set_duty_cycle("PWM0", 100)
 
     def test_pwm_duty_cycle_invalid_key(self):
@@ -154,26 +148,31 @@ class TestPwmSetup:
         PWM.start("PWM0", 0)
         with pytest.raises(ValueError):
             PWM.set_duty_cycle("PWM0", 101)
+        PWM.cleanup()
 
     def test_pwm_duty_cycle_invalid_value_negative(self):
         PWM.start("PWM0", 0)
         with pytest.raises(ValueError):
             PWM.set_duty_cycle("PWM0", -1)
+        PWM.cleanup()
 
     def test_pwm_duty_cycle_invalid_value_string(self):
         PWM.start("PWM0", 0)
         with pytest.raises(TypeError):
             PWM.set_duty_cycle("PWM0", "a")
+        PWM.cleanup()
 
     def test_pwm_frequency_invalid_value_negative(self):
         PWM.start("PWM0", 0)
         with pytest.raises(ValueError):
             PWM.set_frequency("PWM0", -1)
+        PWM.cleanup()
 
     def test_pwm_frequency_invalid_value_string(self):
         PWM.start("PWM0", 0)
         with pytest.raises(TypeError):
             PWM.set_frequency("PWM0", "11")
+        PWM.cleanup()
 
     def test_pwm_freq_non_setup_key(self):
         with pytest.raises(RuntimeError):

test/test_utilities.py

@@ -0,0 +1,11 @@
+import pytest
+
+import CHIP_IO.Utilities as UT
+
+class TestUtilities:
+    def test_invalid_set_1v8_with_string(self):
+        assert not UT.set_1v8_pin_voltage("yaystring")
+
+    def test_invalid_set_1v8_with_outofbounds_value(self):
+        assert not UT.set_1v8_pin_voltage(0.5)
+        assert not UT.set_1v8_pin_voltage(4.5)